Abstract:The strengthening of timber beams with carbon-fibre-reinforced polymers (CFRP) has been widely used in the last decades to enhance the behaviour of historical or new timber structures, usually for bending. While considerable improvement in capacity and ductility is typically achieved, the increase in stiffness was, in many cases, well short of analytical expectations, which tend to overestimate stiffness. This study addresses the problem by investigating the underlying mechanical behaviour using experimental, analytical, and numerical tools on a sample of Norway spruce (Picea abies) beams reinforced with carbon-fibre fabric. In the experimental program, each beam is tested for bending with and without CFRP reinforcement in order to determine specimen-specific stiffness increase on an individual basis. The reinforcement yielded an increase of 27% in capacity, 53% in ultimate displacement, and 133% in compliance, verifying its efficiency. Axial compression tests on an independent sample are also performed to verify modulus of elasticity in compression. Numerical computations based on a beam model and a three-dimensional finite element model are performed with the introduction of separate moduli of elasticity for tension and compression in timber. Inverse computation using the experimental load–deflection curves yielded the moduli and the compression yield stress of timber to provide the best match between tests and simulations. The mean difference of only 6% in stiffness between FEM and the tests is obtained. The dominance of normal stresses in the longitudinal direction is found, in correspondence with the experimentally observed tensile failure of timber (apart from a few defected specimens). Compression yield stresses are within 7% (beam model) and 2% (FEM) error compared with the control axial tests. The differences between FE simulations and tests in ultimate load and compliance are within 1%. This study concludes that the application of CFRP in the composite beams enables the determination of timber material properties opposed to pure timber beams without reinforcement, and the adoption of separate moduli of elasticity for tension and compression leads to adequate modelling of reinforced timber beams.

New four-point bending test protocol for the strength grading of timber: relationship between local and global modulus of elasticity (MOE) of maritime pine

Bending Stiffness of Bamboo-Concrete Composite (BCC) Beams under Short-Term Loads

Bending Performance of Nail-Laminated Bamboo-Timber Panels Made with Glubam and Fast-Grown Plantation Chinese Fir

An Experimental Study of Composite Columns Filled with Eucalyptus nitens Timber under Axial Compression

Measuring elastic constants of wood through static bending using a strain gauge

Bending Strength and Stiffness of Portuguese Maritime Pine Utility Poles

Comparison between static modulus of elasticity, non-destructive testing moduli of elasticity and stress-wave speed in white spruce and lodgepole pine wood

Influence of Test Method on the Determination of Tensile Strength Perpendicular to Grain of Timber for Civil Construction

Experimental, Analytical, and Numerical Assessments for the Controversial Elastic Stiffness Enhancement of CFRP-Strengthened Timber Beams

Predicted and Experimental Bending Behaviour of Glulam Bonded by RPF Adhesive

Influence of test methodology on the characterization of the parallel-to-grain timber embedment strength and foundation modulus of dowels

Full elastic properties characterization of wood by ultrasound using a single sample

Moisture and short-term time-dependent behavior of Norway spruce clear wood under compression perpendicular to the grain and rolling shear

Static Analysis of Wooden Beams Strengthened with FRCM-PBO Composite in Bending

A novel identification method for obtaining bending moment–curvature relations of wood stems based on digital image correlation and SDOF analysis

Tensile and Impact Bending Properties of Chemically Modified Scots Pine

Assessment of Bending Properties of Sawn and Glulam Blackwood in Portugal

Particle image velocimetry technique and ultrasound method to obtain the modulus of elasticity of Bertholletia excelsa wood

The Effect of the Loading Frequency on the Dynamic Bending Strength of Spruce Wood

Comparative Study on Complete Characterisation of Elastic–Ductile Compressive Behaviour of Aged and New Norway Spruce Timber

Modulus Testing in Indirect Tension Mode