Abstract:Lithium superionic conductor (LISICON) Li1.3Al0.3Ti1.7(PO4)3 (LATP) is known as a high lithium-ion conductive solid electrolyte. The top-down approach was utilized in this work to synthesize LATP in which Ag with concentrations of 1, 2, 4, 6, 8 wt% was incorporated in the host material and the performance of the fabricated solid electrolyte was examined and compared with that of the pristine material. Substitution of Li+ by Ag+ in LATP structure resulted in bulk conductivity of 1.1 × 10–3 S cm−1 and grain boundary conductivity of 1.0 × 10–3 S cm−1 at 25 °C for the optimum Ag concentration of 4 wt%. The calcination process was performed in several temperature steps to prevent the release of volatile substances. To obtain a pure LATP structure, phase analyses were performed using X-ray diffraction (XRD) patterns to improve the synthesis conditions. High density, low unwanted and amorphous phases and increased ionic conductivity were achieved by applying sintering process and optimizing the amounts of additives. Effective surface area of about 16 g m−2 was measured using Brunauer–Emmett–Teller (BET) analysis. Negligible decomposition of the products was observed by employing thermal analyses (TGA/DSC). The bulk conductivity of the fabricated solid electrolyte is among the highest reported bulk conductivity for LATP and the grain boundary conductivity revealed by electrochemical impedance spectroscopy (EIS) test is higher than other reported values for LATP. So, the fabricated solid electrolyte is recommended for using in electrically charged solid-state lithium batteries.

Boosting electrochemical properties of Li0.33La0.55TiO3-based electrolytes with Ag incorporation

Microscopic Origin of the Ionic Transport Behaviors in Solid Electrolytes for Li Batteries

Engineered interfaces between perovskite La2/3xLi3xTiO3 electrolyte and Li metal for solid-state batteries

Excess Li2O Additives to Promote Grain Boundary Growth and Improve Ionic Conductivity of LiTa2PO8 Solid Electrolytes

Effect of Bi2O3 on the ion migration and interfacial properties of Li0.33La0.557TiO3 solid electrolytes

Increasing Ionic Conductivity in Li 0.33 La 0.56 TiO 3 Thin-Films Via Optimization of Processing Atmosphere and Temperature

Realizing fourfold enhancement in conductivity of perovskite Li0.33La0.557TiO3 electrolyte membrane via a Sr and Ta co-doping strategy

Effect of Sn or Ta doping on the microstructure and total conductivity of perovskite Li0.24La0.587TiO3 solid electrolyte

Ag-modification argyrodite electrolytes enable high-performance for all-solid-state lithium metal batteries

Fabrication and characterization of Ag-doped Li1.3Al0.3Ti1.7(PO4)3 solid electrolyte with high ionic conductivity

Enhancement of Density and Ionic Conductivity for Garnet-Type Li5La3Ta2O12 Solid Electrolyte by Self-Consolidation Strategy

Remarkably Improved Ionic Conductivity and Lithium Metal Compatibility of LLZTO-Li4(BH4)3I Composite Solid-State Electrolyte

Te doping effect on the structure and ionic conductivity of LiTa2PO8 solid electrolyte

A Multilayer Ceramic Electrolyte for All-Solid-State Li Batteries

Achieving Efficient and Stable Interface Between Metallic Lithium and Garnet-Type Solid Electrolyte Through a Thin Indium Tin Oxide Interlayer

Microstructure and ionic conductivity of Li0.5-La0.5(Ti1-Nb )O3 solid-state electrolytes

Stabilization of Li0.33La0.55TiO3 Solid Electrolyte Interphase Layer and Enhancement of Cycling Performance of LiNi0.5Co0.3Mn0.2O2 Battery Cathode with Buffer Layer

Enhanced Critical Current Density in the Garnet Oxide Electrolyte by a Silver Interlayer

In-situ interfacial passivation and self-adaptability synergistically stabilizing all-solid-state lithium metal batteries

Preparing Two-Dimensional Ordered Li0.33 La0.557 TiO3 Crystal in Interlayer Channel of Thin Laminar Inorganic Solid-State Electrolyte towards Ultrafast Li+ Transfer

Sol–gel Preparation and Electrochemical Properties of La-doped Li4Ti5O12 Anode Material for Lithium-Ion Battery