Abstract:All-solid-state lithium batteries (ASSLBs) are regarded as the next-generation energy storage devices due to their superior safety and potential high energy density. In ASSLBs, a composite solid electrolyte is the most competitive candidate. The interface between the cathode and composite electrolyte and the interface between ceramic and polymers are important factors affecting the performance of solid-state batteries. The interface between the superionic conductor and polymer electrolyte (polyvinylidene fluoride) was modified by in situ synthesis of a pyrochlore-type La2Sn2O7 (LSO) ceramic layer on the surface of Li6.4La3Zr1.4Ta0.6O12 (LLZTO). The synthesis of LSO consumes La in LLZTO, increases the concentration of lithium ions in LLZTO, and significantly improves the conductivity of the composite electrolyte (). Compared with the pristine sample (3.15 × 10–5 S cm–1), the conductivity of %LSO-CSE was improved by an order of magnitude (as high as 1.30 × 10–4 S cm–1). At the same time, the lithium-ion transference number of %LSO-CSE and %LSO-CSE was 0.42 and 0.44, respectively (%LSO-CSE was 0.36). Meanwhile, the pyrochlore structure of LSO has the characteristics of fast energy storage and conversion, so the full cell LiFePO4||Li showed superior rate capability and cycling stability. As anticipated, the discharge capacities of LiFePO4|%LSO-CSE|Li were 141.4 mA h g–1 (1 C) and 128.1 mA h g–1 (2 C), respectively. However, the discharge capacities of pristine batteries without LLZTO modification were 122.5 mA h g–1 (1 C) and 88.7 mA h g–1 (2 C). After 400 cycles, the discharge capacity of the LiFePO4|%LSO-CSE|Li remained at 110.6 mA h g–1, the Coulomb efficiency was 99.4%, and the capacity retention rate was 72% compared to 75.5 mA h g–1, 98, and 49% for the pristine one, respectively. In addition, the transfer printing (TP) technology was used to improve the interface between the cathode and the solid-state electrolyte, which immensely increased the energy density (without aluminum foil). Compared with the original interface impedance of 379 Ω, the interface impedance was significantly reduced to 213 Ω. This uniquely developed combined with the TP technology can provide an effective approach for the development of all-solid-state batteries.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsami.1c09692.SEM images and EDS maps of ; particle size distribution of LLZTO; optical photographs of the tensile test of the composite electrolyte membrane; electronic conductivity of ; and galvanostatic cycles of Li|%LSO-CSE|Li (PDF)This article has not yet been cited by other publications.

Effect of Bi2O3 on the ion migration and interfacial properties of Li0.33La0.557TiO3 solid electrolytes

Tape-Casting Li0.34La0.56TiO3 Ceramic Electrolyte Films Permit High Energy Density of Lithium-Metal Batteries

Influence of Bi2O3 additive on the electrochemical performance of Na3.1Y0.1Zr1.9Si2PO12 inorganic solid electrolyte

High-performance lithium metal batteries based on composite solid-state electrolytes with high ceramic content

Preparation and electrochemical properties of LLZO co-doping with Al and Ti for all solid-state battery

Engineered interfaces between perovskite La2/3xLi3xTiO3 electrolyte and Li metal for solid-state batteries

Microstructure and ionic conductivity of Li0.5-La0.5(Ti1-Nb )O3 solid-state electrolytes

Stable Lithium-Ion Conducting Perovskite Lithium–strontium–tantalum–zirconium–oxide System

Realizing fourfold enhancement in conductivity of perovskite Li0.33La0.557TiO3 electrolyte membrane via a Sr and Ta co-doping strategy

Effect of Sr and Nb co-doped on the total conductivity of Li0.5La0.5TiO3 ceramic electrolytes

Influence of Sintering Additives on Li+ Conductivity and Electrochemical Property of Perovskite-Type Li3/8Sr7/16Hf1/4Ta3/4O3

Stabilization of Li0.33La0.55TiO3 Solid Electrolyte Interphase Layer and Enhancement of Cycling Performance of LiNi0.5Co0.3Mn0.2O2 Battery Cathode with Buffer Layer

Effect of Sintering Temperature and Holding Time on Ionic Conductivity for Li6.4La3Zr1.4Ta0.6O12 Electrolyte

Interface Improvement of Li 6.4 La 3 Zr 1.6 Ta 0.6 O 12 @La 2 Sn 2 O 7 and Cathode Transfer Printing Technology with Splendid Electrochemical Performance for Solid-State Lithium Batteries

A High Air‐Stability and Li‐Metal‐Compatible Li3+2xP1−xBixS4−1.5xO1.5x Sulfide Electrolyte for All‐Solid‐State Li–Metal Batteries

Effect of Sn or Ta doping on the microstructure and total conductivity of perovskite Li0.24La0.587TiO3 solid electrolyte

The Effects of the Size and Content of BaTiO 3 Nanoparticles on Solid Polymer Electrolytes for All-Solid-state Lithium-Ion Batteries

Boosting electrochemical properties of Li0.33La0.55TiO3-based electrolytes with Ag incorporation

Interface Improvement of Li6.4La3Zr1.6Ta0.6O12@La2Sn2O7 and Cathode Transfer Printing Technology with Splendid Electrochemical Performance for Solid-State Lithium Batteries.

A Multilayer Ceramic Electrolyte for All-Solid-State Li Batteries

LLTO-containing heterogeneous composite electrolyte with a stable interface enabling solid-state lithium metal batteries