Abstract:All-solid-state lithium batteries (ASSLBs) are regarded as the next-generation energy storage devices due to their superior safety and potential high energy density. In ASSLBs, a composite solid electrolyte is the most competitive candidate. The interface between the cathode and composite electrolyte and the interface between ceramic and polymers are important factors affecting the performance of solid-state batteries. The interface between the superionic conductor and polymer electrolyte (polyvinylidene fluoride) was modified by in situ synthesis of a pyrochlore-type La2Sn2O7 (LSO) ceramic layer on the surface of Li6.4La3Zr1.4Ta0.6O12 (LLZTO). The synthesis of LSO consumes La in LLZTO, increases the concentration of lithium ions in LLZTO, and significantly improves the conductivity of the composite electrolyte (). Compared with the pristine sample (3.15 × 10–5 S cm–1), the conductivity of %LSO-CSE was improved by an order of magnitude (as high as 1.30 × 10–4 S cm–1). At the same time, the lithium-ion transference number of %LSO-CSE and %LSO-CSE was 0.42 and 0.44, respectively (%LSO-CSE was 0.36). Meanwhile, the pyrochlore structure of LSO has the characteristics of fast energy storage and conversion, so the full cell LiFePO4||Li showed superior rate capability and cycling stability. As anticipated, the discharge capacities of LiFePO4|%LSO-CSE|Li were 141.4 mA h g–1 (1 C) and 128.1 mA h g–1 (2 C), respectively. However, the discharge capacities of pristine batteries without LLZTO modification were 122.5 mA h g–1 (1 C) and 88.7 mA h g–1 (2 C). After 400 cycles, the discharge capacity of the LiFePO4|%LSO-CSE|Li remained at 110.6 mA h g–1, the Coulomb efficiency was 99.4%, and the capacity retention rate was 72% compared to 75.5 mA h g–1, 98, and 49% for the pristine one, respectively. In addition, the transfer printing (TP) technology was used to improve the interface between the cathode and the solid-state electrolyte, which immensely increased the energy density (without aluminum foil). Compared with the original interface impedance of 379 Ω, the interface impedance was significantly reduced to 213 Ω. This uniquely developed combined with the TP technology can provide an effective approach for the development of all-solid-state batteries.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsami.1c09692.SEM images and EDS maps of ; particle size distribution of LLZTO; optical photographs of the tensile test of the composite electrolyte membrane; electronic conductivity of ; and galvanostatic cycles of Li|%LSO-CSE|Li (PDF)This article has not yet been cited by other publications.

Influence of Sintering Additives on Li+ Conductivity and Electrochemical Property of Perovskite-Type Li3/8Sr7/16Hf1/4Ta3/4O3

Highly Dense Perovskite Electrolyte with a High Li+ Conductivity for Li–ion Batteries

Li-Ion Conduction and Stability of Perovskite Li3/8Sr7/16Hf1/4Ta3/4O3.

Effect of Li2O Sintering Aid on Sintering Characteristics and Electrical Conductivity of LSGM Electrolyte for Solid Oxide Fuel Cell

Realizing fourfold enhancement in conductivity of perovskite Li0.33La0.557TiO3 electrolyte membrane via a Sr and Ta co-doping strategy

Influence of Dry‐ and Wet‐milled LLZTO Particles on the Sintered Pellets

Interface Improvement of Li 6.4 La 3 Zr 1.6 Ta 0.6 O 12 @La 2 Sn 2 O 7 and Cathode Transfer Printing Technology with Splendid Electrochemical Performance for Solid-State Lithium Batteries

Excess Li2O Additives to Promote Grain Boundary Growth and Improve Ionic Conductivity of LiTa2PO8 Solid Electrolytes

Stable Lithium-Ion Conducting Perovskite Lithium–strontium–tantalum–zirconium–oxide System

Effect of Sintering Temperature and Holding Time on Ionic Conductivity for Li6.4La3Zr1.4Ta0.6O12 Electrolyte

Interface Improvement of Li6.4La3Zr1.6Ta0.6O12@La2Sn2O7 and Cathode Transfer Printing Technology with Splendid Electrochemical Performance for Solid-State Lithium Batteries.

Rational Design of Strontium Antimony Co-Doped Li7La3Zr2O12 Electrolyte Membrane for Solid-State Lithium Batteries

Remarkably Improved Ionic Conductivity and Lithium Metal Compatibility of LLZTO-Li4(BH4)3I Composite Solid-State Electrolyte

Enhanced grain boundary ionic conductivity of LiTa2PO8 solid electrolyte by 75Li2O-12.5B2O3-12.5SiO2 sintering additive

Improvement of stability and solid-state battery performances of annealed 70Li2S–30P2S5 electrolytes by additives

Engineered interfaces between perovskite La2/3xLi3xTiO3 electrolyte and Li metal for solid-state batteries

Li-ion conductivity and stability of hot-pressed LiTa 2 PO 8 solid electrolyte for all-solid-state batteries

Improved Ionic Conductivity and Li Dendrite Suppression Capability toward Li 7 P 3 S 11 -Based Solid Electrolytes Triggered by Nb and O Cosubstitution

Constructing Effective Interfaces for Li1.5Al0.5Ge1.5(PO4)(3) Pellets to Achieve Room-Temperature Hybrid Solid-State Lithium Metal Batteries

Effect of Bi2O3 on the ion migration and interfacial properties of Li0.33La0.557TiO3 solid electrolytes

Effect of Sn or Ta doping on the microstructure and total conductivity of perovskite Li0.24La0.587TiO3 solid electrolyte