Abstract:Abstract The low corrosion resistance of Mg alloys is the major challenge that slows down the actual application of these lightweight materials. Magnesium has a more negative standard reduction potential than common alloying elements — aluminum and zinc. The formation of local galvanic couples was reported in AZ31-AZ91 alloys due to precipitation of secondary phases, and it was suggested that these galvanic couples provided initiation sites for localized pitting corrosion. Scanning Kelvin probe force microscopy (SKPFM) technique is a precise tool to study the Volta potential distribution on surfaces. Since the lateral resolution of SKPFM maps can reach several nanometers, the technique can be used to detect the deformation-induced formation of nano-particles and phases nucleates. However, the precision of the measurements is affected by several factors: tip-sample distance, humidity, the roughness of the surface and tip characteristics, i.e. tip radius, conductivity, and stiffness. Taking into account that magnesium surface is commonly covered by the self-forming oxide layer, which is reducing electrical sensitivity of the tip, the sample preparation and handling can be considered the major factor that affects the quality of measurements by SKPFM. The aim of our work was to investigate different alternative sample preparation methods for SKPFM and to compare the results (Volta potential maps and topography) with the optical, Scanning Electron Microscopy and Energy Dispersive Spectroscopy maps. The samples were prepared by mechanical polishing, mechanical polishing followed by chemical etching and mechanical polishing followed by ion-milling. For our study, we used a laboratory hot-rolled magnesium-aluminum alloy samples and analysis were focused on typical metallurgical features: surface topography, intermetallic nano-particules and phases nucleates, grain boundary precipitates and grain boundaries.

Local galvanic corrosion analysis on cast Mg-Ca binary alloy using scanning Kelvin probe force microscopy

Quantitative analysis on surface potentials of impurities and intermetallic compounds dispersed in Mg alloys using scanning Kelvin probe force microscopy and ultraviolet photoelectron spectroscopy

Initial micro-galvanic corrosion behavior between Mg2Ca and α-Mg via quasi-in situ SEM approach and first-principles calculation

Comparative, Real-Time in Situ Monitoring of Galvanic Corrosion in Mg-Mg2Ca and Mg-MgZn2 Couples in Hank's Solution

Localized Corrosion of Magnesium Alloys in NaCl Solutions Explored by Scanning Electrochemical Microscopy in Feedback Mode

Microgalvanic Corrosion of Mg–Ca and Mg–Al–Ca Alloys in NaCl and Na2SO4 Solutions

The Effects of ECAP, Mn and Ca Elements on the Microstructure and Corrosion Properties of Magnesium Alloys Were Investigated

In-situ AFM and quasi-in-situ studies for localized corrosion in Mg-9Al-1Fe-(Gd) alloys under 3.5 wt.% NaCl environment

In Vitro Corrosion of As-Extruded Mg–Ca Alloys—the Influence of Ca Concentration

Effect of Sample Preparation on Volta Potential Measurements of Plastically Deformed Mg-Al Alloys

The effects of Ca on the microstructure, mechanical and corrosion properties of extruded Mg-2Zn-0.5Mn alloy

Susceptibility of rare-earth-magnesium alloys to micro-galvanic corrosion

Initial localized corrosion induced by multiscale precipitates in the new generation high-strength Al-Zn-Mg-Cu alloy

Linking the effect of localised pitting corrosion with mechanical integrity of a rare earth magnesium alloy for implant use

Use of Amperometric and Potentiometric Probes in Scanning Electrochemical Microscopy for the Spatially-Resolved Monitoring of Severe Localized Corrosion Sites on Aluminum Alloy 2098-T351

Corrosion Behavior of Pure Mg Based on Generation/Collection and Feedback Modes of Scanning Electrochemical Microscopy

Possibilities and Limitations of Scanning Electrochemical Microscopy of Mg and Mg Alloys

Quasi‐"In‐Situ" Analysis of the Reactive Liquid‐Solid Interface during Magnesium Corrosion using Cryo‐Atom Probe Tomography

Effect of the Ca2Mg6Zn3 Phase on the Corrosion Behavior of Biodegradable Mg-4.0Zn-0.2Mn-xCa Alloys in Hank’s Solution

Exfoliation Corrosion of As-Extruded Mg–1Li–1Ca: the Influence of the Superficial Layer

Electrochemical Corrosion Characterization of As-Cast Mg-7Li Alloy