Abstract:Abstract The low corrosion resistance of Mg alloys is the major challenge that slows down the actual application of these lightweight materials. Magnesium has a more negative standard reduction potential than common alloying elements — aluminum and zinc. The formation of local galvanic couples was reported in AZ31-AZ91 alloys due to precipitation of secondary phases, and it was suggested that these galvanic couples provided initiation sites for localized pitting corrosion. Scanning Kelvin probe force microscopy (SKPFM) technique is a precise tool to study the Volta potential distribution on surfaces. Since the lateral resolution of SKPFM maps can reach several nanometers, the technique can be used to detect the deformation-induced formation of nano-particles and phases nucleates. However, the precision of the measurements is affected by several factors: tip-sample distance, humidity, the roughness of the surface and tip characteristics, i.e. tip radius, conductivity, and stiffness. Taking into account that magnesium surface is commonly covered by the self-forming oxide layer, which is reducing electrical sensitivity of the tip, the sample preparation and handling can be considered the major factor that affects the quality of measurements by SKPFM. The aim of our work was to investigate different alternative sample preparation methods for SKPFM and to compare the results (Volta potential maps and topography) with the optical, Scanning Electron Microscopy and Energy Dispersive Spectroscopy maps. The samples were prepared by mechanical polishing, mechanical polishing followed by chemical etching and mechanical polishing followed by ion-milling. For our study, we used a laboratory hot-rolled magnesium-aluminum alloy samples and analysis were focused on typical metallurgical features: surface topography, intermetallic nano-particules and phases nucleates, grain boundary precipitates and grain boundaries.

Quantitative analysis on surface potentials of impurities and intermetallic compounds dispersed in Mg alloys using scanning Kelvin probe force microscopy and ultraviolet photoelectron spectroscopy

Local galvanic corrosion analysis on cast Mg-Ca binary alloy using scanning Kelvin probe force microscopy

Effect of Sample Preparation on Volta Potential Measurements of Plastically Deformed Mg-Al Alloys

Interfacial characterization and its influence on the corrosion behavior of Mg-SiO2 nanocomposites

Investigating electrochemical corrosion at Mg alloy-steel joint interface using scanning electrochemical cell impedance microscopy (SECCIM)

Quantifying the influence of secondary phases on corrosion in multicomponent Mg alloys using X-ray computed microtomography

Corrosion behavior characterization of as extruded Mg-8Li-3Al alloy with minor alloying elements (Gd, Sn and Cu) by scanning Kelvin probe force microscopy

In-situ AFM and quasi-in-situ studies for localized corrosion in Mg-9Al-1Fe-(Gd) alloys under 3.5 wt.% NaCl environment

Analyzing Galvanic Corrosion Behavior of Metal Alloys Based on First-Principles Simulations

Susceptibility of rare-earth-magnesium alloys to micro-galvanic corrosion

Initial micro-galvanic corrosion behavior between Mg2Ca and α-Mg via quasi-in situ SEM approach and first-principles calculation

Possibilities and Limitations of Scanning Electrochemical Microscopy of Mg and Mg Alloys

Quantifying the influence of microstructure on the corrosion of Mg-Li alloys by using X-ray CT

Theoretical Analysis of the Galvanic Corrosion Behavior of Mg-Ge Binary Alloy

Construction and analysis of surface phase diagrams to describe segregation and dissolution behavior of Al and Ca in Mg alloys

Effect of Ultrasonic Treatment during Solidification on Corrosion Behavior of Mg-3Al-1Zn and Mg-4Zn Magnesium Alloys

High-throughput calculations combining machine learning to investigate the corrosion properties of binary Mg alloys

TEM Observation of Interfaces Between Particles in Al-Mg Alloy Powder Compacts Prepared by Pulse Electric Current Sintering

Quasi-in-situ STEM-EDS Insight into the Role of Ag in the Corrosion Behaviour of Mg-Gd-Zr Alloys

Understanding the Effect of Electrochemical Properties and Microstructure on the Microgalvanic Corrosion of Mg Alloys via Phase-Field Simulations

Initial localized corrosion induced by multiscale precipitates in the new generation high-strength Al-Zn-Mg-Cu alloy