Abstract:This study was carried out to evaluate the effect of acid etching versus laser etching of dentin surface on the bonding of Composite and Compomer restorative materials to dentin surface by studying microleakage at the dentin-filling interface, compositional analysis of dentin surface, and Scanning Electron Microscopic (SEM) study of the bonding area. 120 freshly extracted premolar teeth were divided according to surface treatment into three groups. Group I (Acid etching group) contained thirty teeth. Twenty teeth were selected to assess microleakage by forming standardized class V cavity on the buccal surface of the selected teeth. Then, teeth were subdivided into two subgroups with 10 teeth in each. Subgroup (i) delivered composite filling while subgroup (ii) delivered compomer filling according to manufacturer instructions. microleakage at the dentin-filling interface of teeth was examined using dye penetration method. dye penetration scores at occlusal and gingival margins were recorded and tabulated. Five dentin surfaces of five teeth from group I were etched by acid then prepared for compositional analysis of dentin surface by Infra-Red (IR) Spectroscopy. Another Five dentin surfaces were etched by acid then prepared for (SEM) assessment. Group II (Laser etching group) contained ninety teeth, twenty teeth were used for assessing microleakage after laser etching taking similar steps to that of acid etching. Thirty dentin surfaces of thirty teeth were etched by laser with different parameters then prepared for compositional analysis of dentin surface by IR Spectroscopy. Thirty dentin surfaces of thirty teeth were etched by laser with different parameters then prepared for SEM assessment. Group III (Untreated group) contained ten teeth that were left untreated. Five dentin surfaces of five teeth were subjected to IR Spectroscopy assessment. Five dentin surfaces of five teeth were prepared for SEM assessment. The results revealed that acid etching of dentin surface resulted in significant less leakage compared to laser etching. IR Spectroscopy revealed changes in dentin surface structure indicating that there was a reaction occurred by the acid and laser etching. SEM assessment showed more openings of dentinal tubules in case of acid etching, while in case of laser etching, there were a surface structural changes with a melting and fusion dentin surface. Acid etching of dentin gives better results on the bonding of Composite and Compomer filling materials than laser etching and thus gives more successful clinical condition. Further investigations are needed by using different types of laser to get more benefit from applications of laser clinically.

Comparative Evaluation of Dentin Surface after Preparation by Diamond Bur and Oscillating Tip, with and without Etching

Surface roughness of restoration margin preparations: a comparative analysis of finishing techniques

Effect of Different Burs On The Properties of Dentin Surfaces During Tooth Preparation

Effect of different grit sizes of diamond rotary instruments for tooth preparation on the retention and adaptation of complete coverage restorations.

Prophylometric and SEM analyses of four different finishing methods

A Comparative Analysis of Enamel Surface Roughness Following Various Interproximal Reduction Techniques: An Examination Using Scanning Electron Microscopy and Atomic Force Microscopy

Comparison of Two Means for Enamel Polishing after Debonding——observation of Enamel Surface under SEM

Surface roughness of nanofill and nanohybrid composite resin and ormocer-based tooth-colored restorative materials after several finishing and polishing procedures

Scanning electron microscopic observations of human dentine after cavity preparation by ultrasonic device

Enamel Surface Roughness after Debonding: A Comparative Study using Three Different Burs

Effect of bleaching agents and whitening dentifrices on the surface roughness of human teeth enamel

Comparative Study Of Electric Handpiece And Air-Turbine Handpieces After Tooth Prepare For Veneer

SEM Evaluation of Tooth Surface after a Composite Filling Removal Using Er:YAG Laser, Drills with and without Curettes, and Optional EDTA or NaOCl Conditioning

Comparative study of the effect of laser irradiation and acid etching surface treatment on bonding of some dental restorative materials To dentin surface

Enamel surface roughness following debonding resin clean up using high speed air-turbine and electric handpieces. In vitro study

Comparative Evaluation of Smear Layer and Debris on the Canal Walls prepared with a Combination of Hand and Rotary ProTaper Technique using Scanning Electron Microscope

Comparison of Enamel Surface Roughness after Orthodontic Brackets Debonding and Surface Polishing with Restorative and Orthodontic Composites

Topographical Analysis of Human Enamel after Phosphoric Acid Etching and Er,Cr:YSGG Laser Irradiation

Impact of air-polishing using erythritol on surface roughness and substance loss in dental hard tissue: An ex vivo study

"Comparative evaluation of effect of toothbrush-dentifrice abrasion on surface roughness of resin composites with different filler loading:" An in vitro study

A Comparative SEM Investigation of Smear Layer Remaining on Dentinal Walls by Three Rotary NiTi Files with Different Cross Sectional Designs in Moderately Curved Canals