Abstract:Hot wire laser welding reduces the requirement of wire feeding accuracy and improves wire deposition efficiency with preheating wire by resistance heat. Due to merits like low heat input and high deposition rate, this method has broad potential applications like welding and additive manufacturing. It is a key problem to maintain stable wire transfer in hot wire laser welding since the preheated wire should be kept contacted with the work piece to maintain high temperature. A high-speed imaging system was used to observe wire transfer behaviors, which are divided into three types: fusing transfer, continuous transfer, and wire hit transfer. Only the continuous transfer is the stable wire transfer, which guarantees good weld formation. The wire transfer behavior is determined by wire temperature, and the temperature criterion of wire transfer is obtained by image analysis and temperature measurement. Two characteristic points P1 and P2 on the filler wire were found out, whose temperatures were used to judge wire transfer behaviors. The temperature criterion of the stable wire transfer is interpreted that the temperature of P1 (T P1) must be no more than the wire solidus and the temperature of P2 (T P2) must be no less than the wire liquidus. A heat conduction model of hot wire laser welding was established to calculate T P1 and T P2 for the used 308-L stainless wire. The welding parameters, which made up isothermal surfaces of T P1 = 1398 °C and T P2 = 1454 °C, respectively, the solidus and liquidus of the used wire, were obtained by iteration calculation of wire temperature. The parameters window of the stable wire transfer was located between the two isothermal surfaces. For the stable wire transfer in hot wire laser welding, the resistance heat of the wire cannot exceed the heat which fuses the wire tip outside the molten pool. Meanwhile, the total heat of the wire, including the resistance heat and the heat conducted from the molten pool, must exceed the heat which melts the wire tip inside the molten pool.

Effects of Welding Parameters on Droplet Transfer and Bead Geometry in Laser Welding with Aluminum and Stainless Steel Filler Wires

Droplet Transfer Induced Keyhole Fluctuation and Its Influence Regulation on Porosity Rate during Hybrid Laser Arc Welding of Aluminum Alloys

Effect of energy parameters on droplet transfer behavior and weld formation in laser-arc hybrid welding with cable-type welding wire

Droplet detachment and motion behaviors in laser-MIG hybrid welding of aluminum alloy

Thermal fluid dynamics of the effect of filler wire on deposition rate and bead formation intending plasma arc-based DED

Effect of filler materials on the porosity formation of aluminum alloy by laser welding with filler wire

Droplet transfer characteristics in high-power laser–MAG hybrid welding: Influence of energy parameters

Effect of Welding Parameters on Spatter Formation in Full-Penetration Laser Welding of Titanium Alloys

Effects of process parameters on the depth-to-width ratio of flux-cored wire underwater wet welding

Effect of high-frequency phase shift on metal transfer and weld formation in aluminum alloy double-wire DP-GMAW

Effects of laser energy allocation on weld formation of 9%Ni steel made by narrow gap laser welding filled with nickel based alloy

Mechanism investigation for the influence of laser power on droplet transfer behaviors in laser-MIG hybrid welding

The Effects of Processing Parameters during the Wire Arc Additive Manufacturing of 308L Stainless Steel on the Formation of a Thin-Walled Structure

Influencing mechanism of high speed on the droplet transfer and process stability during high-power laser-arc hybrid welding

Control of Wire Transfer Behaviors in Hot Wire Laser Welding

Effect of laser power, speed and offset on the welding performance of 304 SS/Al2O3 ceramics

Influence of Interwire Distance and Arc Length on Welding Process and Defect Formation Mechanism in Double-Wire Pulsed Narrow-Gap Gas Metal Arc Welding

Microstructure and Mechanical Properties of a Weld Seam from Magnetron High-Current CO2 Welding

Effect of leading and trailing torch configuration on mixing and fluid behavior of laser-gas metal arc hybrid welding

Effect of laser beam incidence angle on weld formation mechanism and corrosion resistance of T2 copper/304 stainless steel

Effect of Filler Wire Composition on Weld Metal Microstructure and Mechanical Properties in X80 Steel Laser Welds