Abstract:High Performance Polymers, Ahead of Print. Polyimide aerogel, presenting an outstanding new material for lightweight protective thermal insulation, has garnered significant attention in the aerospace field. Despite its potential, due to the high production cost of the supercritical drying method used for its preparation, its widespread application is limited. In this research, a series of lightweight polyimide aerogels (F-PIAs, 3,3',4,4'-biphenyl tetracarboxylic dianhydride (s-BPDA) and 4,4'-diaminodiphenyl ether (ODA)) with excellent thermal protection properties were prepared by lyophilization. The findings indicated that F-PIAs (Freeze-dried polyimide aerogels) exhibited comparable physical characteristics to S-PIAs (Supercritical-dried polyimide aerogels), while their preparation cost was even more economical. F-PIAs exhibits excellent flexible and compression behavior (compression strength up to 1.16 MPa, modulus up to 12.8 MPa), which provide a great structural basis for the production of molded thermal insulation protective materials. The average pore diameter of F-PIAs is in the range of 7∼11 nm. The nanoporous structure leads to the gas within the pores of the aerogel producing the Knudsen effect, thereby significantly enhancing the thermal insulation performance of the aerogel. The thermal conductivity of F-PIA-4 (Freeze-dried polyimide aerogels with a solid content of 4%) at room temperature is as low as 0.023 W·m−1·K−1, which is superior to the PIAs (0.043 W·m−1·K−1) prepared by lyophilization in literature. Its thermal diffusion coefficient changes from 0.108 mm2·s−1 to 0.18 mm2·s−1 in the temperature range of 27°C to 200°C, demonstrating good thermal insulation performance at high temperatures. Meanwhile, after heating on a 150°C flat plate for 11 min and 41 s, the surface temperature of F-PIA-4 was only 36.2°C, further verifying its excellent thermal insulation performance. The results of the TGA experiment on F-PIA-4 demonstrated the high-temperature stability of aerogel (Td5% is higher than 523°C, Td10% is higher than 566°C). The exceptional properties of F-PIAs hold significant practical reference value in helping to reduce the manufacturing cost of high-performance aerogel thermal insulation materials, thereby enabling their widespread application in aerospace, military, and civil field.

Lightweight thermo- and heat-resistant composite materials based on polyimide foam

Preparation and Properties of High-Temperature-Resistant, Lightweight, Flexible Polyimide Foams with Different Diamine Structures

Fabrication of Lightweight Polyimide Foams with Exceptional Mechanical and Thermal Properties

Polyimide Foams with Ultralow Dielectric Constants

Fabrication of multifunctional polyimide foams with co-polymerized benzimidazole moieties for excellent thermal insulation and flame retardancy applications

Closed-Cell Rigid Polyimide Foams for High-Temperature Applications: The Effect of Structure on Combined Properties

Hybrid Polyimide Foams with Hyperbranched Organosilicon for High-Temperature Sound Absorption

Short‐cut polyisophthaloyl metaphenylene diamine fiber reinforced polyimide aerogel composites for improving thermal insulation and mechanical performance

Fabrication of rigid polyimide foams via thermal foaming of nadimide-end-capped polyester-amine precursor

Ultralow shrinkage polyimide hybrid aerogel composite enhanced with organic fibers for thermal protection

Modified hollow glass microsphere isocyanate-based polyimide foam composite with improved mechanical and thermal insulation properties

Carbon Foam-Reinforced Polyimide-Based Carbon Aerogel Composites Prepared via Co-Carbonization as Insulation Material

Lightweight and stiff carbon foams derived from rigid thermosetting polyimide foam with superior electromagnetic interference shielding performance

INFLUENCE OF THE CHEMISTRY OF THE FOAMING COMPOSITION ON THERMAL AND MECHANICAL PROPERTIES OF THE FORMING POLYIMIDE FOAM

Bio-Based Poly(Imine-Amide) Materials with Dynamic Covalent Adaptable Networks: Toward Conductive Composites and Thermally Moldable Microcellular Foams

Fiber Reinforced Polyimide Aerogel Composites with High Mechanical Strength for High Temperature Insulation

Fabrication and Characterization of a High-Strength Polyimide/Thermoplastic Polyurethane Composite Aerogel with Hydrophobicity and Low Thermal Conductivity

Synthesis and High-Temperature Energy Storage Performances of Fluorinated Polyimides

Phenylphosphine Oxide Containing Polyimide Matrix Resins for Atomic Oxygen-Resistant Fiber-Reinforced Composites

Polyimide aerogels with low thermal conductivity and high-temperature stable properties prepared by lyophilization for flexible thermal protection

Aramid reinforced polyimide aerogel composites with high‐mechanical strength for thermal insulation material