Abstract:Neat polyimide films are known to be dense and rigid. They are therefore not suitable for use in membranes, sensors and sustainable energy storage applications. In this study, a novel technique has been used to simultaneously improve the porosity, rigidity, damping ability and impact resistance of polyimide membranes. It is demonstrated that dispersion of a small amount of polyaniline copolymer-modified clay of about 0.25-0.5 wt.% into the polyimide matrix resulted in an enhanced storage modulus while maintaining high damping ability and glass transition temperature, Tg. Novel polyimide/substituted polyaniline-copolymer-clay nanocomposite membranes containing poly(N-ethyl-aniline-co-aniline-2-sulfonic-acid)-modified-clay (SPNEAC) was successfully prepared and incorporated into the polyimide matrix to form modified clay/polyimide nanocomposites. UV-Vis analysis of the nanocomposite films shows that the optical transparency of the SPNEAC-PI nanocomposite membranes decreased with increasing SPNEAC concentration due to the high UV-Vis absorption of SPNEAC. Transmittance of about 3% was observed in the nanocomposite membrane containing 5 wt.% modified clay at 500 nm wavelength, which is significantly lower than that for the neat PI membrane of about 36%. The dispersion of SPNEAC containing a high concentration of clay (≥40 wt.% clay), in polyimide matrix, resulted in the attainment of a higher degree of imidization than was possible for the organoclay/polyimide nanocomposite. This behavior is believed to be due to the synergistic interaction between PI and SPNEAC. A correlation of the morphology and elastic modulus of the SPNEAC2/PI nanocomposites shows that at low loading of SPNEAC 2 ≤ 0.5 wt.%, the cross-sectional morphology of the composite is an open, spiky, weblike structure with a storage modulus of about 1 GPa, but it progressively evolves into densely packed microspheroids with storage moduli of ≥2 GPa at 10 wt.% SPNEAC2. The impact energy of SPNEAC/PI composites, calculated from the α-transition peak area, increased with increasing SPNEAC loading and were about 4 times that of neat PI at 10 wt.% SPNEAC.

Bio-Based Poly(Imine-Amide) Materials with Dynamic Covalent Adaptable Networks: Toward Conductive Composites and Thermally Moldable Microcellular Foams

Fabrication of multifunctional polyimide foams with co-polymerized benzimidazole moieties for excellent thermal insulation and flame retardancy applications

Polyhedral oligosilsesquioxane-modified boron nitride enhances the mechanical properties of polyimide nanocomposites

Dual Cross-Linked Networks Reinforced Polyimide Foams with Outstanding Piezoelectric Properties and Heat Resistance Performance

Preparation and Properties of High-Temperature-Resistant, Lightweight, Flexible Polyimide Foams with Different Diamine Structures

Rapidly recyclable, monomer recovery and flame-retardant bio-based polyimine networks

In-situ polymerisation of carbon nanotubes/blended polyimide composites for flexible thermal conductive special-shaped structures

Polyimide-based composites reinforced by carbon nanotube-grafted carbon fiber for improved thermal conductivity and mechanical property

Lightweight thermo- and heat-resistant composite materials based on polyimide foam

Fabrication of Lightweight Polyimide Foams with Exceptional Mechanical and Thermal Properties

High Performance Biomass-Based Polyimides for Flexible Electronic Applications

Structural Optimization of Polyimide Foam via Composition with Hyperbranched Polymer Modified Fluorinated Carbon Nanotubes

Fabrication of High Impact-Resistant Polyimide Nanocomposites with Outstanding Thermomechanical Properties

Synthesis and properties of the amino-functionalized multiple-walled carbon nanotubes/polyimide nanocomposites

High-Performance Polyimides Derived from Biomass: Design, Synthesis, and Properties

Enhanced thermal conductivity in copolymerized polyimide

Novel Synthesis of Polyimide Foams with Aromatic and 1,6-Diaminohexane Imide Bonding

Hybrid Polyimide Foams with Hyperbranched Organosilicon for High-Temperature Sound Absorption

Highly flexible, large scaled and electrical insulating polyimide composite paper with nanoscale polyimide fibers

Mechanically strong and tough polyimide aerogels cross-linked with amine functionalized carbon nanotubes synthesized by fluorine displacement reaction

Synthesis and characterization of functionalized graphene oxide/polyacrylamide nanocomposites using physical adsorbing and chemical grafting and their applications in polyimide matrix