Abstract:Electrospinning as a cost-effective process to synthesize nanofiber with controlled morphology and structure has regained attention in the last decade as result of rapid advancements in nanoscale science and engineering and their applications. Although there are a few works demonstrated the ability to fabricate nano gas sensor using electrospun nanofibers as sensing materials, there are limited works to show the optimization of the sensing performance by understanding the electron transport properties and their sensing mechanism. The overall objective of this work is to electrospun conducting polymer/insulating polymer composite nanofibers (i.e., (+)- camphor-10-sulfonic acid (HCSA) doped polyanline PANI (conductive) blended with PEO (non-conductive)) with different compositions (i.e., 12 to 68 wt.%) and apply them as chemiresistive sensing material to detect ammonia at room temperature. The diameter, defects, and morphology of nanofibers were adjusted by controlling solution composition, processing parameters and their effect toward the sensing performance were also investigated. Viscosity of electrospinning solutions was found to have a pronounced impact on fiber diameter and morphology of PANI/PEO nanofibers. Diameters around 350nm of different compositions of PANI/PEO nanofibers were achieved, where decreasing solution viscosity by increasing the PANI content resulted in a morphology changing from individual fibers to junctions. Although all the compositions of PANI/PEO nanofibers show semiconducting behavior and fit a three dimensional variable hopping range model, the activation energy and hopping distance increased as the PANI content decreased. The PANI/PEO nanofibers exhibited excellent sensitivity towards NH3 with fast response and recovery times where a low detection limit of 0.5 ppm with the sensitivity of 5.6 %/ppm of NH3 was achieved from 26 wt.% PANI/PEO nanofibers. Additionally, the PANI/PEO nanofibers response toward water vapor changed from positive to negative indicating the humidity independent ammonia gas sensor can be fabricated by controlling the composition of PANI/PEO nanofibers.

Polypyrrole–Tungsten Oxide Nanocomposite Fabrication through Laser-Based Techniques for an Ammonia Sensor: Achieving Room Temperature Operation

In Situ Prepared Composite of Polypyrrole and Multi-Walled Carbon Nanotubes Grafted with Sodium Polystyrenesulfonate As Ammonia Gas Sensor with Wide Detection Range

Highly Sensitive NH3 Gas Sensors Based on Novel Polypyrrole-Coated SnO2 Nanosheet Nanocomposites

Low Cost, Flexible, Room Temperature Gas Sensor: Polypyrrole-Modified Laser-Induced Graphene for Ammonia Detection

Fabrication and Ammonia Gas Sensing of Palladium/polypyrrole Nanocomposite

O2 plasma-functionalized SWCNTs and PEDOT/PSS composite film assembled by dielectrophoresis for ultrasensitive trimethylamine gas sensor.

Controllably Fabricated Single Microwires from Pd-WO3•xH2O Nanoparticles by Femtosecond Laser for Faster Response Ammonia Sensors at Room Temperature

Highly selective NH3 gas sensor based on polypyrrole/Ti3C2Tx nanocomposites operating at room temperature

Fabrication of Reproducible and Selective Ammonia Vapor Sensor-Pellet of Polypyrrole/Cerium Oxide Nanocomposite for Prompt Detection at Room Temperature

Nitrogen-doped carbon nano-onions/polypyrrole nanocomposite based low-cost flexible sensor for room temperature ammonia detection

High Performance Gas Sensors Based on In-Situ Fabricated ZnO/polyaniline Nanocomposite: the Effect of Morphology on the Sensing Properties

Nanostructured NiO-polyaniline fibers composite smart material as a room temperature ammonia sensor

MXene/MoS 2 nanosheet/polypyrrole for high-sensitivity detection of ammonia gas at room temperature

A controllably fabricated polypyrrole nanorods network by doping a tetra-β-carboxylate cobalt phthalocyanine tetrasodium salt for enhanced ammonia sensing at room temperature

Electrospun Polyaniline/Poly(ethylene oxide) Composite Nanofibers Based Gas Sensor

Ultrasensitive room-temperature flexible ammonia gas sensor based on Au-functionalized polypyrrole wrapped enriched edge sulfur vacancies MoS 2 nanosheets

Versatile Gas Sensing at Room Temperature: Facile Fabrication of a PANI-PB-ZnO Hybrid Nanocomposite for Detecting Ammonia, Acetone, and Ethanol

Porous Polypyrrole/Polymethylmethacrylate Composite Film Prepared by Vapor Deposition Polymerization of Pyrrole and Its Application for Ammonia Detection

Nanoscale Engineering of Polypyrrole-Silver Oxide Composites for Rapid and Ultrasensitive Room Temperature Carbon Monoxide Detection

Optimizing Ammonia Detection with a Polyaniline−Magnesia Nano Composite

PEDOT/flower-like 1 T-2H MoS2/nitrogen-doped graphene ternary nanocomposite for efficient room temperature real-time monitoring of ammonia