Abstract:Electrospinning as a cost-effective process to synthesize nanofiber with controlled morphology and structure has regained attention in the last decade as result of rapid advancements in nanoscale science and engineering and their applications. Although there are a few works demonstrated the ability to fabricate nano gas sensor using electrospun nanofibers as sensing materials, there are limited works to show the optimization of the sensing performance by understanding the electron transport properties and their sensing mechanism. The overall objective of this work is to electrospun conducting polymer/insulating polymer composite nanofibers (i.e., (+)- camphor-10-sulfonic acid (HCSA) doped polyanline PANI (conductive) blended with PEO (non-conductive)) with different compositions (i.e., 12 to 68 wt.%) and apply them as chemiresistive sensing material to detect ammonia at room temperature. The diameter, defects, and morphology of nanofibers were adjusted by controlling solution composition, processing parameters and their effect toward the sensing performance were also investigated. Viscosity of electrospinning solutions was found to have a pronounced impact on fiber diameter and morphology of PANI/PEO nanofibers. Diameters around 350nm of different compositions of PANI/PEO nanofibers were achieved, where decreasing solution viscosity by increasing the PANI content resulted in a morphology changing from individual fibers to junctions. Although all the compositions of PANI/PEO nanofibers show semiconducting behavior and fit a three dimensional variable hopping range model, the activation energy and hopping distance increased as the PANI content decreased. The PANI/PEO nanofibers exhibited excellent sensitivity towards NH3 with fast response and recovery times where a low detection limit of 0.5 ppm with the sensitivity of 5.6 %/ppm of NH3 was achieved from 26 wt.% PANI/PEO nanofibers. Additionally, the PANI/PEO nanofibers response toward water vapor changed from positive to negative indicating the humidity independent ammonia gas sensor can be fabricated by controlling the composition of PANI/PEO nanofibers.

Fabrication and Ammonia Gas Sensing of Palladium/polypyrrole Nanocomposite

The Research and Application of Polyaniline/Multi-Walled Carbon Nanotubes Composite Sensitive Membrane for Ammonia Gas Detection

In Situ Prepared Composite of Polypyrrole and Multi-Walled Carbon Nanotubes Grafted with Sodium Polystyrenesulfonate As Ammonia Gas Sensor with Wide Detection Range

Highly Sensitive NH3 Gas Sensors Based on Novel Polypyrrole-Coated SnO2 Nanosheet Nanocomposites

Gas sensitivity of a composite of multi-walled carbon nanotubes and polypyrrole prepared by vapor phase polymerization

A Reliable and Fast Hydrogen Gas Leakage Detector Based on Irreversible Cracking of Decorated Palladium Nanolayer Upon Aligned Polymer Fibers

Porous Polypyrrole/Polymethylmethacrylate Composite Film Prepared by Vapor Deposition Polymerization of Pyrrole and Its Application for Ammonia Detection

Composites of Fe2O3 Nanosheets with Polyaniline: Preparation, Gas Sensing Properties and Sensing Mechanism

Gas Sensing Properties of A Composite Composed of Electrospun Poly(Methyl Methacrylate) Nanofibers and in Situ Polymerized Polyaniline

Polyaniline/palladium Nanohybrids for Moisture and Hydrogen Detection

Fabrication of Reproducible and Selective Ammonia Vapor Sensor-Pellet of Polypyrrole/Cerium Oxide Nanocomposite for Prompt Detection at Room Temperature

An easy-fabricated hydrogen gas sensor based on palladium-decorated polyurethane nanofibers

In-Situ Grown Nanostructured Zno Via A Green Approach and Gas Sensing Properties of Polypyrrole/Zno Nanohybrids

Highly selective NH3 gas sensor based on polypyrrole/Ti3C2Tx nanocomposites operating at room temperature

Electrical Conductivity Based Ammonia Sensing Properties of Polypyrrole/MoS2 Nanocomposite

High Performance Gas Sensors Based on In-Situ Fabricated ZnO/polyaniline Nanocomposite: the Effect of Morphology on the Sensing Properties

Electrospun Polyaniline/Poly(ethylene oxide) Composite Nanofibers Based Gas Sensor

Fabrication of Polypyrrole Composite Film Based Trimethylamine Sensor Via Simple Method

Polypyrrole–Tungsten Oxide Nanocomposite Fabrication through Laser-Based Techniques for an Ammonia Sensor: Achieving Room Temperature Operation

A multi-walled carbon nanotube/palladium nanocomposite prepared by a facile method for the detection of methane at room temperature

Gas Sensing Properties of Surface Acoustic Wave Nh3 Gas Sensor Based on Pt Doped Polypyrrole Sensitive Film