Abstract:Organic photovoltaic solar cells can offer advantages of being mechanically flexible and durable, large area devices, lightweight, made from a diversity of materials and low-cost fabrication. Their efficiency is, however, still too low for commercial exploitation. Empirical observations reveal that polymer–fullerene (P3HT:PCBM) based solar cell performance depends on thermal annealing processes employed, especially the annealing temperatures and durations. The annealing parameters are known to influence the energetics and kinetics of the blending process or morphology, but the associated physics is not fully understood. In this work, current density–voltage characteristics of P3HT:PCBM bulk heterojunction organic solar cells, thermally annealed at different temperatures, 65–160 °C post fabrication, were investigated under dark and illuminated conditions, and compared to their as-cast counterparts. In certain electrical regimes, as-cast devices showed higher values of current density in comparison to the corresponding annealed devices. Such performance was attributed to air-borne chemical doping of the as-cast semiconductor layer, which creates electrically conductive percolation pathways within the as-cast devices. We propose that annealing of semiconductors must be a two-step process, which first initiates decrease in conductivity, followed by its increase. As-cast devices P3HT–PCBM bulk heterojunction solar cells prepared under atmospheric conditions were observed to have comparatively superior photovoltaic performance in comparison to thermally annealed devices. The efficiency drop in the annealed counterparts is attributed to dedoping due to thermal annealing. An annealing temperature of ~ 140 °C was found to be optimum for power conversion efficiency in the bulk heterojunction, 1:1 by mass, P3HT:PCBM based solar cells.

Effect of rapid thermal annealing on photovoltaic properties of silicon solar cell fabricated by one-step laser doping in liquid

Rapid Thermal Annealing and Hydrogen Passivation of Polycrystalline Silicon Thin-Film Solar Cells on Low-Temperature Glass

The Striking Influence of Rapid Thermal Annealing on InGaAsP Grown by MBE: Material and Photovoltaic Device

Rapid Thermal Annealing Effects on Passivation Quality of p-TOPCon Silicon Solar Cells

Dark and illuminated J(V) characteristics of thin layered bulk heterojunction P3HT:PCBM sandwich solar cells after thermal treatment

Post-Fabrication Annealing Effects in Polymer-Nanotube Photovoltaic Cells

Effects on Amorphous Silicon Photovoltaic Performance from High-temperature Annealing Pulses in Photovoltaic Thermal Hybrid Devices

Effect of Vacuum Rapid Annealing Treatment on Performance of CIGS Solar Cells

Inverted All-Polymer Solar Cells Based on a Quinoxaline–thiophene/naphthalene-Diimide Polymer Blend Improved by Annealing

Effect of annealing conditions on phosphorus inward diffusion from N + Poly-Si layer in N-type TOPCon solar cells

Quantitative Nanoscale Monitoring the Effect of Annealing Process on the Morphology and Optical Properties of Poly(3-Hexylthiophene)/[6,6]-phenyl C61-butyric Acid Methyl Ester Thin Film Used in Photovoltaic Devices

Post annealing to improve the sheet resistance and uniformity of emitter for enhancing conversion efficiency of mass-produced mc-Si solar cells

Enhancement of inverted organic solar cell parameters by post-production annealing process

Rapid Thermal Annealing Process for Se Thin-Film Solar Cells.

The effect of thermal annealing on defect states, light intensity and photocurrent of organic solar cells

Annealing Effect on Photovoltaic Performance of Hybrid P3ht/In-Situ Grown Cds Nanocrystal Solar Cells

Effect of Thermal Annealing on the Efficiency of Heterojunction Photovoltaic Cells Fabricated Using Poly(3-Hexylthiophene) and Methanofullerene, [6,6]-Phenyl C61-butyric Acid Methyl Ester.

Influence of thermal annealing on microstructure, energetic landscape and device performance of P3HT: PCBM-based organic solar cells

Thermal Annealing Effect on Ultrafast Charge Transfer in All-Polymer Solar Cells with a Non-Fullerene Acceptor N2200

Thermal Assisted Oxygen Annealing for High Efficiency Planar CH3NH3PbI3 Perovskite Solar Cells

Impact of annealing on spiro‐OMeTAD and corresponding solid‐state dye sensitized solar cells