Abstract:Wake-up receivers (WuRXs) help to significantly reduce the average power of the Internet of the Things (loT) hardware systems. To lower the “asleep” power in the idle state, the WuRX structures based on non-standard protocols have been widely studied in prior researches, which can realize a high sensitivity [1] or low power [2]. Compared to the non-standard receivers, there are more design challenges in the standard-compliant WuRXs. For example, a BLE-compliant WuRX operating in the congested 2.4GHz band should be able to handle potentially large interferers including adjacent-channel tone and image, as well as realize a high sensitivity for long-reach access. Therefore, there have been several conventional solutions for the interference-resilient BLE-compliant WuRXs: 1) Single-path down-conversion WuRXs. The interference is handled by an RF filter [3] or a low-noise LO [4] (Fig. 1, top). The WuRX in [3] utilized an FBAR filter to reject the interference from the adjacent channel, resulting in a signal-to-interference ratio (SIR) of −6dB@2MHz, where the loss of FBAR filter degraded the sensitivity to −85dBm. An LC oscillator based LO was adopted in [4] to suppress the adjacent-channel interference by −10dB, but it's at the penalty of 1.2mW power. 2) I/Q-path down-conversion WuRXs. A Hartley WuRX was designed in [5] to reject both 2MHz adjacent-channel interference and image (Fig. 1, middle), as well as improve the sensitivity to −92dBm, while the I/Q downconverters and LO generators dominated the total power consumption. Although the WuRX power was reduced to 352μW by the edge combiner based I/O LO generation, the SIR was limited to −12.5dB due to the spurs and noise accompanying the LO signal. As a result, it's difficult for the conventional WuRX structures to realize both a high SIR and low power consumption.

Super-Regenerative Receiver Wake-Up Radio Solution for 5G New Radio Communications

Turbo-like Iterative Multi-user Receiver Design for 5G Non-orthogonal Multiple Access

A 144 GHz 2.5mW multi-stage regenerative receiver for mm-Wave imaging in 65nm CMOS

Energy Optimization for Mobile Applications by Exploiting 5G Inactive State

A 100mhz-2ghz Wireless Receiver In 40-Nm Cmos For Software-Defined Radio

An Improved Wake-Up Receiver Based on the Optimization of Low-Frequency Pattern Matchers

Analytical and Experimental Performance Analysis of Enhanced Wake-Up Receivers Based on Low-Power Base-Band Amplifiers

A Sub-1-GHz Band High-Dynamic-Range Receiver with Integrated Self-Adaptive Multipart AGC Loops

Self-demodulated receiver at MM-wave range using SiGe technology

An Interference-Resilient 120-Degree-apart Pseudo-I/Q BLE-Compliant Wake-Up Receiver Achieving-21dB SIR,-94dBm Sensitivity, and 4-D Wake-Up Signature

3GPP Release 18 Wake-up Receiver: Feature Overview and Evaluations

Novel Wake-up Scheme for Energy-Efficient Low-Latency Mobile Devices in 5G Networks

Advances and Opportunities in Passive Wake-Up Radios with Wireless Energy Harvesting for the Internet of Things Applications

Receiver Design for Realizing On-Demand WiFi Wake-up using WLAN Signals

Analysis and Design of a Multi-Mode Wake-Up Receiver Based on Direct Envelope Detection in Wireless Sensor Networks

A 3.8-mW 3.5-4-GHz regenerative FM-UWB receiver with enhanced linearity by utilizing a wideband LNA and dual bandpass filters

Energy-Efficient Internet of Things Monitoring with Content-Based Wake-Up Radio

A 55uW 2.4GHz wake-up receiver with offset-based peak detection achieving −90dBm sensitivity for IoT applications

A 55 μ W 2.4 GHz wake-up receiver with offset-based peak detection achieving −90dBm sensitivity for IoT applications

Ultra-Low-Power IoT Communications: A novel address decoding approach for wake-up receivers

Low-Power, High-Data Rate 915 MHz Transceiver with Fully Passive Wake-Up Receiver for Biomedical Implants