Abstract:Pulsed low-pressure carburizing (LPC) and omnidirectional high-pressure gas quenching (HPGQ) are innovative methods for quenching the surface layer. The thermo-chemical treatment carried out by this method reduces quenching geometric deformations, with detailed numerical values not available in the literature due to the short existence of this method.Sixteen toothed elements of EN 20MnCr5 steel were subjected to pulsed low-pressure carburising with omnidirectional jet quenching in 4 groups, varying the process temperature (920C, 960C) and in two groups performing a tempering treatment. The elements were tested before machining by measuring their internal hole diameters, radial runout, roundness and cylindricity. These values were tested again after treatment. The direction of change and the statistical significance of the effect of treatment and its parameters, temperature and tempering were analysed.Thermo-chemical treatment significantly affects geometric changes in diameters, roundness, cylindricity and radial runout compared to elements without heat treatment due to physical transformations occurring during this treatment (p<0.05). Changing the process temperature in the value range of 920C-960C affects the hole diameter (makes it smaller) (p<0.05), but does not affect radial runout, cylindricity and roundness. The observed dimensional changes in diameters have numerically small values (<0.005 mm). The tempering treatment can affect the values of average diameters. Its effect on roundness, cylindricity and radial runout was not observed.In the temperature range studied, the method of pulsed low-pressure carburising + omnidirectional high-pressure gas quenching makes it possible to raise the temperature of the process and shorten its duration without significant geometric changes in the treated elements.The method of pulsed low-pressure carburising and omnidirectional high-pressure gas quenching (HPGQ) ensures the maintenance of reproducible quenching deformations at a level significantly lower than conventional processing methods.The method of pulsed low-pressure carburising together with omnidirectional high-pressure gas quenching (HPGQ) is a method that has been used briefly in the industry, and there are few reports on it to date.

Water-controlled quenching heat treatment method of 42CrMo bars

Investigation of quenching stress of 42CrMo treated by alternately timed quenching process

Quenched Depth of 20mnsi Steel Bar in the Process of Controlled-Cooling

Research on 40Cr Laser Quenching Process for Guide Rail

Impact of single-piece flow thermo-chemical treatment process conditions on hole quenching deformation

Optimization of Heat Treatment for 38Si7 Spring Steel with Excellent Mechanical Properties and Controlled Decarburization

Effect of Intermittent Water Spray Quenching on the Wear Resistance of Forged Grinding Balls Made of Steel 70SiMnCr

Effect of Different Quenching Methods on the Microstructure and Mechanical Properties of 30MnB5NbTi

Numerical Simulation of Water Air Alternative Quenching Process for Large Steel Forging

Optimization of heat treatment process after vacuum carburizing of 18Cr2Ni4WA steel

Research on laser quenching process of 20CrMnMo gears by finite element method and experiment

Study of an Economical and Effective Heat Treatment Method to Improve the Performance of Gear Steels

Bottom Spray Quenching Device

Study on the Heat Treatment Process of SXQ500/550DZ35 Steel QLT for the Seat Ring and Guide Vane of a Hydropower Station

Steel tube inner wall grinding device with water spraying dust removal function

A Study On Laser Quenching Technology Of Automobile Gear

Experimental Study on Vacuum Carburizing Process for Low-Carbon Alloy Steel

Effect of Quenching and Tempering Treatment on Microstructure and Mechanical Properties of CSS-42L Bearing Steel

Optimization of Heat Treatment Process of Drilling Rod Material Containing Indium for Water Conservancy Machinery

Research and Manufacture of Heavy Duty Horizontal Rotary Spray Quenching Equipment

Effect of Post-Plasma Nitrocarburized Treatment on Mechanical Properties of Carburized and Quenched 18Cr2Ni4WA Steel