Abstract:Smart dielectrics with self-adaptive capabilities can exhibit desirable electric field-grading performance as the applied electric field exceeds a critical value. However, the conventional approaches to such dielectrics need heavy doping rate, which will not only increase the interface thermal resistance and limit the improvement of thermal conductivity, but also severely sacrifice the mechanical property. In this contribution, a new type of electric field-grading co-continuous phase composite (EP/SiCcf) composed of epoxy resin and SiC ceramic foam was prepared to realize tunable nonlinear conductive performance, while simultaneously improving thermal and mechanical properties. Results show that there is no percolation threshold for all EP/SiCcf composites. The volume loadings of EP/SiCcf composites range from 8.7 vol% to 15.6 vol%, while the nonlinear coefficient subjected to potential barrier height increases from 2.1 to 4.5 and the switching field tuned by barrier width decreases from 1008 V/mm to 686 V/mm. The EP/SiCcf40 still exhibits sharp thermal conductivity enhancement of about 1000% and glass transition temperature enhancement of 10.8 °C. The surface temperature fluctuation over time during heating and cooling has illustrated the prospective application of thermal management capability. In addition, the dynamic mechanical analysis reveals that all EP/SiCcf composites have the significantly improved storage modulus and crosslinking density ascribed to the intact SiC skeleton. The novel co-continuous phase composite provides a new approach for global enhancement of smart dielectric composites in potential applications.

In situ fabrication of continuously graded Si3N4 ceramics via DC field-assisted hot pressing

Optimization of Microstructure to Improve Si3n4 Ceramics with Thermal Conductivity and Mechanical Properties: Effect of Si and Α-Si3n4 Powder Composition

Interfacial Regulation and Fracture Mechanism of Al–Si/SiC Composites Infiltrated under Super-Gravity Field

In situ formation of Si3N4–SiC nanocomposites through polymer-derived SiAlCN ceramics and spark plasma sintering

Enhanced Mechanical/electrical Properties of in Situ Synthesized SiC-TiB2 Ceramic Composites by Reactive Hot-Pressing Sintering

DC assisted electric field on the improvement of the nonlinear electrical conductivity of SiC/LDPE field grading composites

Study on the mechanical properties and microstructure of Al2O3/nano-SiC multiphase ceramics

In‐situ combustion synthesis of spherical Si@Si3N4 granules

Fabrication, structure and properties of in-situ reinforced Si3N4 ceramics from sol-gel derived oxide-additive-coated powders

Fabrication of silicon nitride with high thermal conductivity and flexural strength by hot‐pressing flowing sintering

Fabrication of Si3N4 ceramics substrates with high thermal conductivity by tape casting and gas pressure sintering

Fabrication of Si 3 N 4 ceramics with high thermal conductivity and flexural strength via novel two-step gas-pressure sintering

Simultaneous improvement in porosity and strength of porous β-Si3N4 ceramics by formation of ultrafine fibrous grains

Rapid fabrication of Si3N4 ceramics with gradient appearance and microstructure

Fabrication of (SiC-AlN)/ZrB2 Composite with Nano-Micron Hybrid Microstructure via PCS-Derived Ceramics Route

Synthesis and Mechanical Properties of Highly Porous Ultrafine-Grain Si3N4 Ceramics Via Carbothermal Reduction-Nitridation Combined with Liquid Phase Sintering

Tunable nonlinear conductive behavior without percolation threshold and high thermal conductivity of epoxy resin/SiC ceramic foam co-continuous phase composites

Surface modification and ablation behaviors of nitrogen-doped C/C-ZrC-SiC composites via hot isostatic pressing

Effects of MgSiN2 Addition and Post-Annealing on Mechanical and Thermal Properties of Si3N4 Ceramics

In-situ Reaction Synthesis of Porous Si2N2O-Si3N4 Multiphase Ceramics with Low Dielectric Constant Via Silica Poly-Hollow Microspheres

Fabrication of continuously porous SiC–Si3N4 composite using SiC powder by extrusion process