Abstract:Methods and results of the experimental and numerical investigation of the 1D heat transfer properties of a multifunctional syntactic foam. Top: experimental setup with schematic representation of the position of the thermocouples and boundary conditions; bottom left: microstructure of a representative sample of epoxy/hollow glass microspheres (HGM)/phase change material (PCM) syntactic foam; bottom right: temperature as a function of time in the heating experiment for the thermocouple located at 13 mm from the hot surface for different foam compositions. Data from the experiments (dotted line) and from the numerical modeling (solid line). Syntactic foams are lightweight porous composites obtained by the addition of hollow glass microspheres (HGMs) to a polymer matrix. This work experimentally and numerically investigates the thermal behavior of epoxy‐based syntactic foams with enhanced multifunctionality produced by incorporating microencapsulated phase change materials (PCMs) as functional fillers, providing thermal energy storage and temperature stabilization due to its large latent heat of melting. Foams are fabricated using varying ratios of HGMs (0–40 vol%) and PCM (0–40 vol%) to achieve tuned densities and thermal properties with a total filler content of up to 40 vol%. A one‐dimensional numerical heat transfer model based on the enthalpy method is presented to simulate the thermal behavior of these materials. The model accurately incorporates the specific heat and thermal conductivity of the foam components, as well as the latent heat absorption during PCM melting (up to 68 J/g). The model is experimentally validated by demonstrating good agreement with the measurements of transient temperature profiles during heating tests on the foam samples. The validated tool is then leveraged to model the thermal response of the foams under a sinusoidally varying heat source, similar to the possible real applicative scenarios. These results can help optimize foam compositions balancing energy storage density, heat transfer properties, and structural support for lightweight energy storage systems. Potential applications include high‐efficiency thermal management in battery packs, electronic cooling, solar energy storage, and sustainable temperature‐controlled buildings. Highlights Foams with 0–40 vol% PCM and 0–40 vol% HGM show up to 68 J/g latent heat. 1D numerical model accurately captures thermal conductivity and PCM phase change. Validated model simulates thermal response under sinusoidal heat, optimizing foam composition. Foams act as thermal reservoirs, maintaining up to 5°C lower surface temperatures than epoxy.

Thermal Mechanical Testing of Low Density Thermoplastic Foam

Impact Properties of Uniaxially Thermoformed Auxetic Foams

Microcellular Thermoplastic Polyurethanes and Their Flexible Properties Prepared by Mold Foaming Process with Supercritical CO2

An experimental toolbox for the physical characterization of thermal insulating polymeric foams

Comparative study of chemical and physical foaming methods for injection-molded thermoplastic polyurethane

LFT foam - Lightweight potential for semi-structural components through the use of long-glass-fiber-reinforced thermoplastic foams

Compressive Mechanical Behavior and Corresponding Failure Mechanism of Polymethacrylimide Foam Induced by Thermo-Mechanical Coupling

Tuning High and Low Temperature Foaming Behavior of Linear and Long-Chain Branched Polypropylene via Partial and Complete Melting

Study of rigid cross-linked PVC foams with heat resistance

Closed-Cell Rigid Polyimide Foams for High-Temperature Applications: The Effect of Structure on Combined Properties

Experimental approach for characterizing the nonlinear, time and temperature‐dependent constitutive response of open‐cell polyurethane foams

Modeling the thermal behavior of multifunctional syntactic foams containing phase change materials for heat management applications

Thermo-mechanical characterization of carbon-based ceramic foams for high temperature space application

Experimental and Numerical Analyses of Thermal Failure of Rigid Polyurethane Foam

Study on temperature gradient of ultra-thick foam sandwich composite structure during curing

Preparation, Characterization, and Mechanical Properties of Microcellular Poly(Aryl Ether Ketone) Foams

Experimental method for creep characterization of polymeric foam materials in media immersion

Characterization and modeling of the uniaxial thermo-mechanical compressive behavior of polymethacrylimide (PMI) foam at different temperatures

Unintended consequences: Assessing thermo-mechanical changes in vinyl nitrile foam due to micro-computed X-ray tomographic imaging

Fabrication and Characterization of Flexible High Performance Thermoplastic Foams Derived from Rigid Polyetherketoneketone Via a VOC-free Foaming Method

Post-curing Effect on the Chemical Structure and Its Relationship with Heat Resistance and Thermal-Mechanical Properties of Crosslinked PVC Foams