Abstract:Methods and results of the experimental and numerical investigation of the 1D heat transfer properties of a multifunctional syntactic foam. Top: experimental setup with schematic representation of the position of the thermocouples and boundary conditions; bottom left: microstructure of a representative sample of epoxy/hollow glass microspheres (HGM)/phase change material (PCM) syntactic foam; bottom right: temperature as a function of time in the heating experiment for the thermocouple located at 13 mm from the hot surface for different foam compositions. Data from the experiments (dotted line) and from the numerical modeling (solid line). Syntactic foams are lightweight porous composites obtained by the addition of hollow glass microspheres (HGMs) to a polymer matrix. This work experimentally and numerically investigates the thermal behavior of epoxy‐based syntactic foams with enhanced multifunctionality produced by incorporating microencapsulated phase change materials (PCMs) as functional fillers, providing thermal energy storage and temperature stabilization due to its large latent heat of melting. Foams are fabricated using varying ratios of HGMs (0–40 vol%) and PCM (0–40 vol%) to achieve tuned densities and thermal properties with a total filler content of up to 40 vol%. A one‐dimensional numerical heat transfer model based on the enthalpy method is presented to simulate the thermal behavior of these materials. The model accurately incorporates the specific heat and thermal conductivity of the foam components, as well as the latent heat absorption during PCM melting (up to 68 J/g). The model is experimentally validated by demonstrating good agreement with the measurements of transient temperature profiles during heating tests on the foam samples. The validated tool is then leveraged to model the thermal response of the foams under a sinusoidally varying heat source, similar to the possible real applicative scenarios. These results can help optimize foam compositions balancing energy storage density, heat transfer properties, and structural support for lightweight energy storage systems. Potential applications include high‐efficiency thermal management in battery packs, electronic cooling, solar energy storage, and sustainable temperature‐controlled buildings. Highlights Foams with 0–40 vol% PCM and 0–40 vol% HGM show up to 68 J/g latent heat. 1D numerical model accurately captures thermal conductivity and PCM phase change. Validated model simulates thermal response under sinusoidal heat, optimizing foam composition. Foams act as thermal reservoirs, maintaining up to 5°C lower surface temperatures than epoxy.

Modeling the thermal behavior of multifunctional syntactic foams containing phase change materials for heat management applications

Thermophysical Properties of Multifunctional Syntactic Foams Containing Phase Change Microcapsules for Thermal Energy Storage

A New Strategy for Enhanced Latent Heat Energy Storage with Microencapsulated Phase Change Material Saturated in Metal Foam

Microencapsulated Phase Change Material (MEPCM) Saturated in Metal Foam As an Efficient Hybrid PCM for Passive Thermal Management: A Numerical and Experimental Study

Enhanced Thermal Management with Microencapsulated Phase Change Material Particles Infiltrated in Cellular Metal Foam

Thermo-Mechanical Behavior of Novel EPDM Foams Containing a Phase Change Material for Thermal Energy Storage Applications

Development of Novel Polypropylene Syntactic Foams Containing Paraffin Microcapsules for Thermal Energy Storage Applications

Numerical Analysis on a Latent Thermal Energy Storage System with Phase Change Materials and Aluminum Foam

Experimental and Numerical Studies on Melting Process of Phase Change Materials (pcms) Embedded in Open-Cells Metal Foams

Melting of Phase Change Materials Inside Metal Foams with Uniform/graded Porosity: Pore-scale Simulation

Numerical simulation on thermal behavior of partially filled metal foam composite phase change materials

Modeling Metal Foam Enhanced Phase Change Heat Transfer in Thermal Energy Storage by Using Phase Field Method

Experimental and Numerical Study on Melting of Phase Change Materials in Metal Foams at Pore Scale

Experimental Study on Heat Transfer During Melting in Metal and Carbon Foam Saturated with Phase-Change Materials for Temperature Control in Electronic Devices

Heat transfer enhancement for thermal energy storage using metal foams embedded within phase change materials (PCMs)

Numerical investigation on thermal behaviors of two-dimensional latent thermal energy storage with PCM and aluminum foam

Effect of filling configurations on melting heat transfer characteristic of phase change materials partially filled with metal foam

Thermal response of annuli filled with metal foam for thermal energy storage: An experimental study

Melting of Phase Change Materials with Volume Change in Metal Foams

Phase Change Behaviour Study of PCM Tanks Partially Filled with Graphite Foam

Experimental Study on the Temperature Control Characteristics of Graphite Foam-Based Composite Phase Change Materials