Abstract:CoCrNi medium entropy alloy additive part was fabricated by laser directed energy deposition process. Based on an optimized additive manufacturing process parameters, the microstructure, tensile properties and corrosion performance in the XOY and XOZ planes were compared to learn the anisotropic properties of the additive part. The majority of the additive parts consisted of equiaxed grains, a small proportion consisted of elongated needle-like grains. The equiaxed and elongated needle-like grains in the XOY plane were finer compared to that in the XOZ plane. The corrosion electrochemical activity is uniform in the XOY plane, but varies at different heights in the XOZ plane base on scanning vibrating electrode technique results. Electron backscatter diffraction results near the fracture indicated a larger and relatively more homogeneous residual stress peak in the XOY plane. The tensile and yield strengths in the XOZ plane were lower than those in the XOY plane by approximately 98.5 MPa and 19.1 MPa. While the elongation in the XOZ plane was more than twice as high as that in the XOY plane. The reason for the anisotropic tensile behavior was the strong texture in the XOY plane and the relatively random grain orientation in the XOZ plane. Single crystal and polycrystalline molecular dynamics were used to simulate the anisotropic tensile properties in the XOZ and XOY planes. Single crystal simulation results showed that the maximum stress was 19.0 GPa and elongation was 13.0% when the stretching was along the [110] crystal orientation. The minimum stress was 17.1 GPa and elongation is 11.1% elongation when the stretching was along the [11 ] crystal orientation. Anisotropy existed for CrCoNi alloys in terms of tensile properties along different orientations. Polycrystalline simulation in the XOY plane results showed that the main cause of anisotropy between them was the tangling of the 1/6 dislocations and the 1/6 dislocations, which caused obstacles to dislocation motion and thus improved the strength of CoCrNi additive parts. High tensile strength in the XOY plane, not the XOZ plane, was attributed to 1/6 and 1/6 dislocation tangles at the (1 0)/(115) planes.

Dislocation slips assisted grain rotation and specific texture evolution in a CoCrNi medium entropy alloy

Texture Evolution and Plastic Deformation Mechanism of Cold-Drawn Co-Cr-Ni-Mo Alloy

Differences in Texture Evolution from Low-Entropy to High-Entropy Face-Centered Cubic Alloys During Tension Test

Revealing the deformation mechanisms of symmetric tilt grain boundaries in CoCrNi medium-entropy alloy

Quantifying chemical fluctuations around medium-range orders and its impact on dislocation interactions in equiatomic CrCoNi medium entropy alloy

Atomistic insights into the deformation mechanism of a CoCrNi medium entropy alloy under nanoindentation

In-situ observations of static recrystallization and texture formation in a cold-rolled CoCrFeMnNi high entropy alloy

Grain size dependent microstructure and texture evolution during dynamic deformation of nanocrystalline face-centered cubic materials

In-situ EBSD study of deformation behavior of nickel-based superalloys during uniaxial tensile tests

Mechanical behaviors and texture evolution of CoCrFeNi high-entropy alloy under shear-tension deformation

Texture evolution during multi-pass cold rolling and annealing of Ti-2Al-1.5Mn alloy

Tensile behaviors and hetero-deformation-induced hardening mechanisms in medium entropy alloys with dual gradients of grain size and coherent nanoprecipitate

Anisotropic microstructure, properties and molecular dynamics simulation of CoCrNi medium entropy alloy fabricated by laser directed energy deposition

Deformation substructure development in AlXCoCrFeNi (X = 0, 0.3) high entropy alloy under different influencing factors

Analysis of the Ni-5%at.W Alloy Substrate Texture Evolution at Different Strain Levels Using the EBSD Technique

Transition of twinning behavior in CoCrFeMnNi high entropy alloy with grain refinement

Texture evolution and slip mode of a Ti-5.5Mo-7.2Al-4.5Zr-2.6Sn-2.1Cr dual-phase alloy during cold rolling based on multiscale crystal plasticity finite element model

Anomalous dislocation response to deformation strain in CrFeCoNiPd high-entropy alloys with nanoscale chemical fluctuations

Plastic deformation mechanism of CoCrxNi medium entropy alloys

Hierarchical Grain Size and Nanotwin Gradient Microstructure for Improved Mechanical Properties of a Non-Equiatomic CoCrFeMnNi High-Entropy Alloy

Chemical short-range ordering accompanies shear band initiation in CrCoNi medium entropy alloy