Abstract:The utilization of plastic solid wastes for sustainable energy production is a crucial aspect of the circular economy. This study focuses on pyrolysis as an effective method to convert this feedstock into renewable drop-in fuel. To achieve this, it is essential to have a comprehensive understanding of feedstock composition, pyrolysis process parameters, and the physicochemical characteristics of the resulting fuel, all correlated with engine combustion parameters. Considering this full value chain, this study provides the first unbiased and up-to-date benchmark of polypropylene and polystyrene pyrolysis oils (PPO and PSO) produced in an industrial-grade batch reactor. The pyrolysis process was optimized to achieve ultra-high liquid yield levels of 92% for PPO and 98% for PSO with minimum energy consumption. After post-processing, blending with diesel, and normative fuel analytics, combustion/emission tests involving 20 species preceded under fully controllable conditions using a state-of-the-art single-cylinder research engine. The fuel analysis results revealed significant disparities between the properties of PPO and PSO. PPO exhibited a diverse carbon structure, resulting in very low density and high volatility. On the other hand, PSO was predominantly composed of aromatics, leading to low viscosity and poor auto-ignition properties. Engine tests showed that PPO blends exhibited combustion characteristics similar to diesel, while PSO blends exhibited significant differences, particularly during the premixed combustion stage attributed to pilot injection . Following the combustion response, the addition of PPO had minimal impact on emissions, while PSO acted as an emission enhancer, resulting in over twofold increase in particulate matter at high loads. Consequently, PSO showed elevated carbon monoxide and hydrocarbon emissions due to the higher contribution of aromatics. Ultimately, this study challenges the prevailing perception of plastic-derived fuels as "dirty". By implementing feedstock segregation to minimize polystyrene content, it is possible to achieve a fossil substitute level of 40% while meeting all emission and safety regulations for diesel engines with a minimum economic burden.

Catalytic Copyrolysis of Used Waste Plastic and Lubricating Oil Using Cu-Modification of a Spent Fluid Catalytic Cracking Catalyst for Diesel-like Fuel Production

Catalytic co‐pyrolysis of waste rubber and waste lubricants with waste copper catalyst into value‐added fuel

Production of diesel-like fuel by catalytic co-pyrolysis of waste cooking oil and waste lubricating oil—an alternate energy source

Enhancing light fuel production through catalytic pyrolysis of municipal mixed plastic waste over activated spent FCC catalyst

Combined Activated Carbon with Spent Fluid Catalytic Cracking Catalyst and MgO for the Catalytic Conversion of Waste Polyethylene Wax into Diesel-like Hydrocarbon Fuels

Enhanced Oil Yield by Catalytic Pyrolysis of Thermoplastics Using Cost-Effective Spent FCC and BaCO3 and Its Valorization to Gasoline and Diesel Grade Fuel via Fractionation

A lab scale waste to energy conversion study for pyrolysis of plastic with and without catalyst: Engine emissions testing study

An experimental assessment on a diesel engine powered by blends of waste-plastic-derived pyrolysis oil with diesel

Polypropylene Plastic Waste Conversion to Lubricants over Ru/TiO 2 Catalysts

Study on the kinetics of catalytic pyrolysis of single and mixed waste plastics by spent FCC catalyst

Sustainable biodiesel production from waste olive oil: Utilizing olive pulp-derived catalysts for environmental and economic benefits

Efficient Synthesis of Nickel-Molybdenum/USY-Zeolite Catalyst for Eliminating Impurities (N, S, and Cl) in the Waste Plastic Pyrolysis Oil: Dispersion Effect of Active Sites by Surfactant-Assisted Melt-Infiltration

A Study of Catalytic Copyrolysis of Sewage Sludge and Waste Plastics Using Taguchi Method

Processing renewable and waste-based feedstocks with fluid catalytic cracking: Impact on catalytic performance and considerations for improved catalyst design

Waste limescale derived recyclable catalyst and soybean dregs oil for biodiesel production: Analysis and optimization

Catalyst-mediated pyrolysis of waste plastics: tuning yield, composition, and nature of pyrolysis oil

Evaluating the properties of a novel diesel-like fuel produced by biochar-assisted catalytic cracking of waste motor oil

Chemical Conversion of Fischer–Tropsch Waxes and Plastic Waste Pyrolysis Condensate to Lubricating Oil and Potential Steam Cracker Feedstocks

Experimental investigation to identify the type of waste plastic pyrolysis oil suitable for conversion to diesel engine fuel

Energy extraction from waste plastics and its optimization study for effective combustion and cleaner exhaust engaging with water and cetane improver: A response surface methodology approach