Emergent Phenomena and Computer Worlds

J. Casti

DOI: https://doi.org/10.1007/BFb0028515

1996-11-09

Abstract:

What problem does this paper attempt to address?

Evaluation of Waste Plastic Pyrolysis Oil Performance with Diethyl Ether Additive on Insulated Piston Diesel Engine

S. Padmanabhan,C. Joel,Linda Joel,Obulareddy Yuvatejeswar Reddy,K.G.D. Sri Harsha,S. Ganesan

DOI: https://doi.org/10.46488/nept.2021.v20i05.025

2021-12-25

Nature Environment and Pollution Technology

Abstract:Considering the amount of waste plastics has risen significantly, energy may be extracted from it. Not only is it possible to dispose of waste plastics by converting them to fuel, but it is also possible to extract energy from them. Our research is motivated by the prospect of using waste plastics as a source of energy through waste plastic pyrolysis oil (WPPO). The innovation of this research is that it will assess the efficiency of plastic pyrolysis oil derived from Low-Density Polyethylene (LDPE) on a Thermal Barrier Coated (TBC) piston engine. The incremental ratio of WPPO to pure diesel with the addition of diethyl ether (DEE) was determined and its output and exhaust emission standards were evaluated using a direct injection single cylinder low heat rejection diesel engine. The results for the WPPO blends were promising as with TBCW20DEE10 demonstrating a 5 to 15% increase in carbon monoxide under different load conditions. TBCW20DEE10 confirmed a greater reduction of hydrocarbons varying from 5 to 12 %. At half load condition, TBCW20DEE10 emits approximately 3.5 % less unit of smoke.

English Else
Extraction and characterization of waste plastic pyrolysis oil for diesel engines

Krishnaraj Janarthanan,Periyasamy Sivanandi

DOI: https://doi.org/10.1016/j.jclepro.2022.132924

IF: 11.1

2022-09-15

Journal of Cleaner Production

Abstract:In this research work, the fuel extraction process from waste plastics through the thermal cracking method is explored. The pyrolysis process was carried out at a wide range of temperatures in the absence of oxygen. About 78% (w/w) of the liquid yield was extracted between the effective pyrolysis temperatures of 370 °C - 380 °C, resulting in a calorific value of 38.53 MJ/kg. The obtained plastic pyrolysis fuel was then characterized by thermogravimetric study, FTIR and GC-MS analysis. Thermogravimetric analysis indicates that the structures of natural plastic break at 200 °C and fully decompose at 300 °C. The presence of alkanes and aromatic components in the plastic pyrolysis fuel was confirmed through FTIR analysis. Further GC-MS studies on fuel samples have proven that hydrocarbon compounds exist within the C7–C40 range. Plastic pyrolysis fuel obtained from waste plastics is found to have similar fuel properties to diesel. The plastic pyrolysis fuel was tested in a single cylinder four stroke variable compression ratio diesel engine with different blends of plastic pyrolysis fuel and diesel ranging from 0% to 100% at varied engine loads ranging from 25% to 100%. The engine performance and exhaust emissions were studied and compared with conventional diesel fuel operation. The research revealed that the engine can operate on plastic pyrolysis fuel at full load, has a 6% improvement in brake thermal efficiency as well as 4% reduction in UBHC and 2% reduction of CO emissions, albeit NOx emissions were significantly greater. The results confirmed that plastic pyrolysis fuel could be a viable replacement option for diesel.

environmental sciences,green & sustainable science & technology,engineering, environmental
An experimental assessment on a diesel engine powered by blends of waste-plastic-derived pyrolysis oil with diesel

Katarzyna Januszewicz,Jacek Hunicz,Paweł Kazimierski,Arkadiusz Rybak,Tomasz Suchocki,Kamil Duda,Maciej Mikulski

DOI: https://doi.org/10.1016/j.energy.2023.128330

IF: 9

2023-07-10

Energy

Abstract:The utilization of plastic solid wastes for sustainable energy production is a crucial aspect of the circular economy. This study focuses on pyrolysis as an effective method to convert this feedstock into renewable drop-in fuel. To achieve this, it is essential to have a comprehensive understanding of feedstock composition, pyrolysis process parameters, and the physicochemical characteristics of the resulting fuel, all correlated with engine combustion parameters. Considering this full value chain, this study provides the first unbiased and up-to-date benchmark of polypropylene and polystyrene pyrolysis oils (PPO and PSO) produced in an industrial-grade batch reactor. The pyrolysis process was optimized to achieve ultra-high liquid yield levels of 92% for PPO and 98% for PSO with minimum energy consumption. After post-processing, blending with diesel, and normative fuel analytics, combustion/emission tests involving 20 species preceded under fully controllable conditions using a state-of-the-art single-cylinder research engine. The fuel analysis results revealed significant disparities between the properties of PPO and PSO. PPO exhibited a diverse carbon structure, resulting in very low density and high volatility. On the other hand, PSO was predominantly composed of aromatics, leading to low viscosity and poor auto-ignition properties. Engine tests showed that PPO blends exhibited combustion characteristics similar to diesel, while PSO blends exhibited significant differences, particularly during the premixed combustion stage attributed to pilot injection . Following the combustion response, the addition of PPO had minimal impact on emissions, while PSO acted as an emission enhancer, resulting in over twofold increase in particulate matter at high loads. Consequently, PSO showed elevated carbon monoxide and hydrocarbon emissions due to the higher contribution of aromatics. Ultimately, this study challenges the prevailing perception of plastic-derived fuels as "dirty". By implementing feedstock segregation to minimize polystyrene content, it is possible to achieve a fossil substitute level of 40% while meeting all emission and safety regulations for diesel engines with a minimum economic burden.

energy & fuels,thermodynamics
Performance, Combustion, and Emission analysis of diesel engine fuelled with pyrolysis oil blends and n-propyl alcohol-RSM optimization and ML modelling

K. Sunil Kumar,Raviteja Surakasi,S Gopal Krishna Patro,Nikhil Govil,M.K. Ramis,Abdul Razak,Prabhakar Sharma,Majed Alsubih,Saiful Islam,T.M.Yunus Khan,Naif Almakayeel,Sanjay Chintakindi

DOI: https://doi.org/10.1016/j.jclepro.2023.140354

IF: 11.1

2024-01-04

Journal of Cleaner Production

Abstract:This experimental work focuses on testing the diesel engine by the replacement of pyrolysis oil extracted from different waste plastics. The novelty of this work is testing the engine performance, combustion, and emission study with the following proportions D90WPO7NP3, D80WPO15NP5, D70WPO23NP7, WPO100, and D100. The pyrolysis oil is extracted from the mixed waste plastics with calcium bentonite as a catalyst and n-propyl alcohol is used as an additive for better igniting developer. From the results, it is found that the performance parameters such as BTE are found to increase in efficiency by 2.2% for the fuel D90WPO7NP3 and decrease in BSFC by 3.1% for the same fuel compared to pure diesel. It is also noticed that the emission properties such as CO 2 , CO, HC, and O 2 content decreased in the order of 5.49%, and 6.2%. 39.2 and 12.5 % as compared to pure diesel. However, there is a slight increase in emissions of NO X due to the presence of uncontrolled enriched constituents in the pyrolysis oil; the increase in NOx emissions is found to be 16.2% compared to diesel fuel at full load conditions. The ML and RSM techniques using ANOVA techniques are adopted to find the least accuracy of data. This shows that the model fits the data well. The linear regression model explains 93.6% of the variation in BTE during training and has 95.9% prediction power. Linear Regression showed good predictive skills, acquiring a high R 2 value of 0.985. It is concluded that pyrolysis oil with n-propyl alcohol as an additive gives a better substitute in the field of automobile applications.

environmental sciences,green & sustainable science & technology,engineering, environmental
Environmental impact of waste plastic pyrolysis oil on insulated piston diesel engine with methoxyethyl acetate additive

Padmanabhan Sambandam,Parthasarathy Murugesan,Vinod Kumar Thangaraj,Muthuraman Vadivel,Muraliraja Rajaraman,Ganesan Subbiah

DOI: https://doi.org/10.1080/10916466.2022.2092498

IF: 1.695

2022-06-29

Petroleum Science and Technology

Abstract:The energy recovery from waste plastics as a prospective fuel source helps to overcome the issues of waste plastic management and the growing fuel shortage. In this article, High-Density Polyethylene (HDPE) plastics are used to convert into waste plastic pyrolysis oil (WPPO) through the pyrolysis process. An experimental investigation is carried out to evaluate the effectiveness of WPPO in a Thermal Barrier Coated piston engine (TBC) with an oxygenated additive of Methoxyethyl acetate (MEA). The incremental ratio of WPPO to pure diesel with the addition MEA and its performance, combustion, and emission characteristics are studied in a direct injection single-cylinder low heat rejection diesel engine. MEA and the coated piston resulted in improved performance of WPPO. Brake-specific fuel consumption is reduced by up to 9% under various load situations. D70W20MEA10 shows carbon monoxide elimination of up to 15% under various load conditions and a hydrocarbon reduction of up to 16%. At half load, D70W20MEA10 produces about 3% less HSU of smoke.

energy & fuels,engineering, chemical, petroleum
Experimental investigation to identify the type of waste plastic pyrolysis oil suitable for conversion to diesel engine fuel

V.L. Mangesh,S. Padmanabhan,P. Tamizhdurai,A. Ramesh

DOI: https://doi.org/10.1016/j.jclepro.2019.119066

IF: 11.1

2020-02-01

Journal of Cleaner Production

Abstract:Plastics for various applications is increasing every year due to outstanding advantages, but after use recycling and disposal have remained a challenge. In this paper, through experiments, we compare properties of pyrolysis oil derived from after use HDPE (High-density polyethylene), LDPE (Low-density polyethylene), PP (Polypropylene)and styrene for their suitability as diesel engine fuel. This experimental study is to identify which type of plastic is suitable for blending with diesel. The physicochemical properties of pyrolysis oil of HDPE, LDPE, PP, and styrene were tested, tabulated and compared with diesel. The physicochemical properties of polypropylene pyrolysis oil (PPO) were found to be superior to the produced pyrolysis oil of HDPE, LDPE, and styrene. The GC-MS(Gas chromatography-mass spectrometry)and FT-IR (Fourier transform-infrared spectroscopy) were taken for pyrolysis oil of HDPE, LDPE, PP, and styrene and compared with diesel. PPO showed lower carbon number chain compounds compared to the other three waste plastics. We selected PPO for diesel engine performance and emission trials based on the results of the above tests. PPO was blended in the ratios of 5%, 10% and 15% with diesel. Combustion analysis showed a increase in cylinder pressure in comparison to diesel values. The heat release rates (HRR) were sharply higher than diesel. Both cylinder pressure and HRRvalues for PPO increased as the blend ratios increased. The emission results showed an increase in carbon monoxide (CO), hydrocarbon (HC)and oxides of Nitrogen (NOx)emissions. The multiple times increase in emissions is due to the presence of unsaturated hydrocarbons and higher carbon number of saturated compounds in PPO. GC-MS tests confirmed the presence of such compounds in PPO. To reduce the unsaturation to negligible levels, we will take up future experiments in hydrogenating PPO with various catalysts and test the performance and emissions in diesel engines.

environmental sciences,green & sustainable science & technology,engineering, environmental
Plastic pyrolytic oils as renewable fuel: improving its physical properties and ignition patterns by waste renewable source—an experimental analysis

Gopinath Soundararajan,Bibin Chidambaranathan,Ashok Kumar Rajendran,Dillibabu Venugopal,Yuvarajan Devarajan

DOI: https://doi.org/10.1007/s11356-024-32668-5

IF: 5.8

2024-03-07

Environmental Science and Pollution Research

Abstract:The increase in plastic products and disposal poses a severe environmental challenge because of their poor biodegradability and undesirable disposal by landfilling. Recycling is the best possible solution to the environmental challenges implemented by the plastic industry. Pyrolysis is a process that converts waste plastics into pyrolytic oil, and it can be used as fuel in a blended form. The viscosity and lubricity of the LDWP (low-density waste polyethylene) pyrolytic oil were lower than standard diesel. Capparis spinosa methyl ester (CME) is blended and experimented with to overcome the lubricity issue of pyrolytic oil. In this investigation, 5%, 10%, and 15% CME were blended with PD20 (20% LDWP oil + 80% diesel) blend on a volume basis. Experiments were conducted to examine the effects of CME on combustion, performance, and emissions using the combination of CME and PD20 blend tested at 0%, 25%, 50%, 75%, and 100% loading conditions. All three ternary mixtures showed enhanced combustion performance and increased NO x and smoke emissions. Due to better combustion, the efficiency of the blend PCD10 (10% CME + 20% LDWP oil + 70% diesel) was higher than the PD20 blend and significantly closer to diesel. Hence, PCD10 is suggested as an alternative to diesel fuel.

environmental sciences
Energy recovery of waste plastics into diesel fuel with ethanol and ethoxy ethyl acetate additives on circular economy strategy

Sambandam Padmanabhan,K. Giridharan,Balasubramaniam Stalin,Subramanian Kumaran,V. Kavimani,N. Nagaprasad,Leta Tesfaye Jule,Ramaswamy Krishnaraj

DOI: https://doi.org/10.1038/s41598-022-09148-2

IF: 4.6

2022-03-29

Scientific Reports

Abstract:Abstract The widespread use of plastic goods creates huge disposal issues and environmental concerns. Increasing emphasis has been paid to the notion of a circular economy, which might have a significant impact on the demand for plastic raw materials. Post-consumer plastics recycling is a major focus of the nation’s circular economy. This study focuses on energy recovery from waste plastics as an alternative fuel source to meet the circular economy demand. Waste plastic fuel produced through pyrolysis has been claimed to be utilized as a substituted fuel. This work focuses to determine the performance and emission standards of Waste Plastic Fuel (WPF) generated from the pyrolysis of High-Density Polyethylene (HDPE) in a single-cylinder Direct Injection Diesel Engine (DIDE). Three different ratios of WPF were combined with 10% ethanol and 10% ethoxy ethyl acetate as an oxygenated additive to create quaternary fuel blends. The ethanol has a low viscosity, a high oxygen content, a high hydrogen-to-carbon ratio as favourable properties, the quaternary fuel results the improved brake thermal efficiency, fuel consumption and reduced emissions. The blend WEE20 exhibits 4.7% higher brake thermal efficiency, and 7.8% reduced fuel consumption compared to the diesel. The quaternary fuel blends demonstrated decreased carbon monoxide of 3.7 to 13.4% and reduced hydrocarbons of 2 to 16% under different load conditions.

multidisciplinary sciences
Extraction and Performance Analysis of Hydrocarbons from Waste Plastic Using the Pyrolysis Process

B. T. Ramesh,Javed Sayyad,Arunkumar Bongale,Anupkumar Bongale

DOI: https://doi.org/10.3390/en15249381

IF: 3.2

2022-12-11

Energies

Abstract:Ecosystem destruction is one of today’s significant challenges due to fast industrialisation and an increasing population. It takes several years for solid trash, such as plastic bottles and super-market bags, to decompose in nature. In addition, plastic disposal techniques such as landfilling, reuse, and incineration pose significant threats to human health and the environment. In this paper, we investigated whether the impact of mixing biodiesel with waste oil from recycled plastic on the resulting fuel mixture’s yields better physical and chemical properties. Consequently, pyrolysis is one of the most advantageous and practical waste disposal methods as it is both environmentally benign and efficient. Pyrolysis is the high-temperature thermal breakdown of solid waste to produce pyrolytic oil. The pyrolytic (plastic) oil produced is converted to a hydrocarbon-rich pyrolytic fuel. Similar to diesel and gasoline, pyrolytic fuel has the same calorific value. Internal combustion engines may operate on pyrolytic fuel without suffering a performance reduction. Researchers examined engine performance and exhaust pollutants. The research discovered that the engine could operate on plastic pyrolysis fuel at full load, enhance brake thermal efficiency by 6–8%, and lower UBHC and CO emissions; however, nitrous oxide (NOx) emissions were noticeably higher. The findings demonstrated the possibility of using plastic pyrolysis fuel as a diesel substitute.

energy & fuels
Optimisation of an experimental and feasibility research on a CRDI diesel engine based on a blend of waste cooking oil and waste plastic oil using RSM: A value addition for disposed waste oil

Manish Kumar,Raghvendra Gautam,Naushad Ahmad Ansari

DOI: https://doi.org/10.1016/j.joei.2024.101564

IF: 6.47

2024-02-16

Journal of the Energy Institute

Abstract:This investigation aims to use a combination of waste cooking oil (WCO) and waste plastic oil (WPO) biodiesel blended with diesel in a common rail direct injection (CRDI) diesel engine. This study examined the effects of (WCO + WPO) blend %, fuel injection timing (FIT), exhaust gas recirculation (EGR), and engine load on the performance and emission of diesel engines. The trials were developed using the central composite design (CCD) approach and the accompanying multiple responses were investigated using response surface methodology (RSM). The WCO biodiesel was produced by the transesterification method, with an 88% yield. Based on the combined effects of the uncertainties from the temperature sensor, load sensor, Brake Thermal Efficiency (BTE), Brake Specific Fuel Consumption (BSFC), and Exhaust Gas Temperature (EGT), carbon monoxide (CO), unburned hydrocarbons (HC), and nitrogen oxides (NOx), the percentage of uncertainty was found to be ±2.53%. The outcomes of the analysis of variance (ANOVA) revealed that the experimental and estimated outputs were in good agreement. R 2 values were determined to be 98.41%, 97.02%, 99.29%, 98.49%, 98.71%, and 98.21% for BTE, EGT, BSFC, HC, CO, and NOx, respectively. The input factors optimised at14% biodiesel, 25 o bTDC FIT, 6% EGR value, and 35% engine load, for which the best output parameters were discovered to be 20.3%, 485.6 K, 370.9g/kWh, 0.18vol.%, 17.8ppmv, and 336.33ppmv for BTE, EGT, BSFC, HC, CO, and NOx, respectively. Validation tests were performed to confirm optimisation findings by setting engine input parameters to optimum levels, which were determined and reported as in an acceptable range.

energy & fuels
Experimental Evaluation of Performance and Combustion Characteristics of Blended Plastic Pyrolysis Oil in Enhanced Diesel Engine

Chonlakarn Wongkhorsub,Wantana Chaowasin,Kampanart Theinnoi

DOI: https://doi.org/10.3390/en15239115

IF: 3.2

2022-12-02

Energies

Abstract:Plastic waste is the largest volume of waste and the most discarded, and it has a direct negative impact on the environment. Therefore, the pyrolysis oil process is an essential and sustainable solution to reduce plastic waste accumulation. However, the plastic pyrolysis fuel performance in diesel engines is reduced due to its lower cetane number. Diesel and pyrolysis oil were blended in ratios of 90:10 (BP10), 80:20 (BP20), 70:30 (BP30), 60:40 (BP40), and 50:50 (BP50) and applied in a single-cylinder diesel engine to investigate the engine performance and exhaust emission. The long ignition delay, thermal efficiency drops, and emission growth were found regarding the higher blended fuel ratios. BP30 was selected to evaluate the performance and combustion characteristics of blended plastic pyrolysis oil and diesel fuel blends by enhancing an unmodified engine using low hydrogen additions (1000 ppm) and advanced timing adjustment. The hydrogen injected into the intake manifold, along with the advanced fuel injection timing (−16.5 CA°BTDC), affected engine performance and emissions (CO, HC, and NO) at 1500 rpm under 25%, 50%, and 75% of the maximum load compared with diesel fuel. The results showed that the hydrogen addition was very positive for both engine performance and emission reduction, as the expanded flammability of the hydrogen promoted a wide range of combustion within the cylinder, whereas the advanced injection timing achieved improved engine performance but produced higher emissions compared to B7 at all engine loads.

energy & fuels
Waste plastic to pyrolytic oil and its utilization in CI engine: Performance analysis and combustion characteristics

R.K. Singh,Biswajit Ruj,A.K. Sadhukhan,P. Gupta,V.P. Tigga

DOI: https://doi.org/10.1016/j.fuel.2019.116539

IF: 7.4

2020-02-01

Fuel

Abstract:<p>For application of pure plastic pyrolytic oil (PPO) several modifications in the engine is required which rejects the utilization of the existing engines while a blend of conventional fuel and PPO can be used with a slight change in engine without having a high impact on engine performance and hence the blends are preferred over the utilization of PPO as crude oil for diesel engines. In this study, the non-catalytic pyrolysis of mixed plastic waste at a temperature of 450 °C is done to obtain high-grade pyrolytic oil having a composition similar to petroleum fuels such as gasoline and diesel. Physical properties of the PPO were analysed, and the compound analysis was done with GC–MS. Further FTIR of PPO and diesel were analysed and compared. Five different ratios of 10, 20, 30, 40 and 50% PPO with diesel in blends were utilized as a fuel in a diesel engine to determine the engine performance and characteristics. The higher presence of PPO in blend increases the brake thermal efficiency (BTE) and reduces specific fuel consumption (SFC) with an increase in load as reported. The presence of PPO results in high heat release and delayed ignition resulting in high in-cylinder pressure. Further high amount of oxygenated compounds in PPO helps in reducing the emission from the combustion. The utilization of PPO with diesel upto 50% in the blend can be used in diesel engines with a slight increase in emission of CO at higher loads.</p>

energy & fuels,engineering, chemical
Effective utilization of waste plastic derived fuel in CI engine using multi objective optimization through RSM

Amit Kumar,Harveer Singh Pali,Manoj Kumar

DOI: https://doi.org/10.1016/j.fuel.2023.129448

IF: 7.4

2024-01-01

Fuel

Abstract:This study provides the prediction that plastic pyrolysis oil (PPO) is equivalent to petroleum diesel in CI engines. The four input parameters have been considered to enhance performance and reduced emissions. The input parameters of engine trials, like fuel blend (PPO and diesel), compression ratio, nanoparticle concentration, and injection timing, were studied with the response surface methodology (RSM) using the central composite rotating design (CCRD) matrix. The main goal is to identify the ideal values of input parameters that will provide the highest achievable brake thermal efficiency (BTE), the lowest possible brake-specific fuel consumption (BSFC), and the lowest possible emission like carbon monoxide (CO), unburnt hydrocarbons (HC) and nitrogen oxides (NOx). The optimal engine output responses for BTE, BSFC, in-cylinder pressure, heat release rate (HRR), and ignition delay, respectively. Along witha composite desirability of 0.89 under optimum operating conditions. After the regression analysis, 16.56% PPO blend ratio, 53.53 ppm Al2O3 nanoparticle concentration, 18.06 compression ratio, and 20.95 °bTDC injection timing were received the optimized engine settings. Optimal engine input parameters were validated through actual engine trials and compared with optimized responses and found satisfactory and acceptable errors (less than 5%). The current study establishes vital input parameters providing the best engine performance, combustion characteristics, and lower emissions during engine trials. So current investigation declared PPO with Al2O3 nanoparticles is potential fuel for the CI engine.

energy & fuels,engineering, chemical
Optimisation of Process Parameters to Maximise the Oil Yield from Pyrolysis of Mixed Waste Plastics

Farjana Faisal,Mohammad Golam Rasul,Ashfaque Ahmed Chowdhury,Islam Jahirul,Md Islam Jahirul

DOI: https://doi.org/10.3390/su16072619

IF: 3.9

2024-03-22

Sustainability

Abstract:The study sought to optimise process parameters of thermal pyrolysis of mixed waste plastic (MWP) to maximise pyrolytic oil yield. High-density polyethylene (HDPE), polypropylene (PP), and polystyrene (PS) were used as feedstocks for pyrolysis. Response surface methodology (RSM) and Box–Behnken design (BBD) were used to optimise the pyrolysis process. The optimisation was carried out by varying three independent variables, namely, reaction temperature (460–540 °C), residence time (30–150 min), and size of MWP feedstock (5–45 mm), to increase the liquid oil yield. A BBD matrix was used to generate the design of the experiments, and 15 experiments were conducted. The highest liquid oil yield of 75.14 wt% was obtained by optimising the operating parameters, which were a reaction temperature of 535.96 °C, a reaction time of 150 min, and a feedstock particle size of 23.99 mm. A model was developed to determine the relationships among the independent variables, and analysis of variance (ANOVA) was used to investigate their impact on maximising oil yield. ANOVA results showed that the temperature and residence time had the maximum impact on oil yield, followed by feedstock size. Physicochemical analysis of the properties of the plastic pyrolytic oil (PPO) revealed that the crude PPO obtained from the MWP had higher water (0.125 wt%) and sulfur content (5.12 mg/kg) and lower flash point (<20 °C) and cetane index (32), which makes it unsuitable for use as an automobile fuel. However, these issues can be resolved by upgrading the PPO using different posttreatment techniques, such as distillation and hydrotreatment.

environmental sciences,environmental studies,green & sustainable science & technology
Critical insights into the effects of plastic pyrolysis oil on emission and performance characteristics of CI engine

Dipankar Saha,Abhijit Sinha,Bidesh Roy

DOI: https://doi.org/10.1007/s11356-021-14919-x

IF: 5.8

2021-07-01

Environmental Science and Pollution Research

Abstract:Pyrolysis is an encouraging solution considering the facts of energy demand and waste plastic management as it produces liquid fuel for compression ignition engine application. This study provides critical insights into the effects of waste plastic oil on the emission and performance characteristics of compression ignition engines. Though most of the studies have shown a negative influence, promising outcomes have been noticed in a few specific cases. A maximum of 71%, 80%, 76%, 71%, 21%, and 13% decrease in nitrogen oxide emission, carbon monoxide emission, unburnt hydrocarbon emission, smoke emission, exhaust gas temperature, and brake-specific fuel consumption, respectively, have been noticed with waste plastic oil or its blends at certain operating conditions. Nevertheless, the presence of long carbon chains, higher aromatic content, and non-homogeneous air-fuel mixture owing to the wide product distribution in plastic oil are the few reasons which affected the emission and performance characteristics of the engines. More rigorous investigations are needed to improve the quality of the fuel and to establish correlations between the fuel properties and pyrolysis parameters. In addition, the effects of incorporating exhaust gas recirculation, emulsification process, and use of additives with waste plastic oil need to be explored more for reducing the emissions with satisfactory engine performance, and in this regard, the use of bio-additives with waste plastic oil can provide a new direction to this research field. Further, studies on the economic feasibility and the impact of waste plastic oil on engine materials are also required.

environmental sciences
Experimental investigation of fuel injection timing effects on a CRDI diesel engine running on hydrogen-enriched waste plastic oil

Tushar Anand,Sumita Debbarma

DOI: https://doi.org/10.1016/j.ijhydene.2024.01.052

IF: 7.2

2024-01-18

International Journal of Hydrogen Energy

Abstract:In response to fossil fuel concerns and the imperative of effective plastic waste management, this study investigates the impact of hydrogen-plastic oil (WPO) blends on a CRDI diesel engine. Six combinations (WPO10, WPO20, WPO30, WPO10 + H 2 , WPO20 + H 2 , WPO30 + H 2 ) are examined across varying loads and fuel injection timings. Notably, WPO10 + H2 (H 2 energy share i.e., 8 lpm) exhibits a 15.1 % increase in brake thermal efficiency, an 11.2 % fuel consumption reduction, improved peak cylinder pressure (66 bar), and maximum heat release rate (40.16 J/°CA) compared to diesel. It also shows reduced emissions of CO, HC, CO 2 , and smoke opacity—34.8 %, 15.1 %, 10.7 %, and 28.5 %, respectively, relative to diesel. Elevated nitrogen oxide (NOx) emissions are observed across all blends. This study underscores the environmental benefits of blending waste plastic oil with diesel, promoting recycling, reducing reliance on traditional diesel, lowering greenhouse gas emissions, and supporting sustainability. Advanced fuel injection timing at higher loads slightly mitigates NOx emissions, while increasing the blend proportion leads to prolonged ignition delays, reduced thermal efficiency, and heightened emissions.

energy & fuels,electrochemistry,chemistry, physical
Experimental Investigation in Compression Ratio on Performance, Combustion and Emission of VCR Engine using Pyrolysis-oil Produced from Waste Plastic Materials

Bablu Alawa,Sankar Chakma

DOI: https://doi.org/10.1016/j.matpr.2022.07.228

2023-01-01

Materials Today: Proceedings

Abstract:The generation of waste plastic is one of the major concerns for the scientific community due to its non biodegradable nature. Plastic has been primarily used in different packaging sectors across the globe and polyolefins are primarily used for this purpose to mitigate the demand. However, the lower recycling rate of waste plastics creates several long-term issues in the ecosystem. Therefore, reducing the waste plastic and producing some valuable chemicals is one of the ideal directions to overcome this issue. In this study, we have reported the production of liquid fuels from waste plastics material through thermo-chemical conversion and analyzed for engine performance, combustion, and emission characteristics in compression ignition (CI) engine. The liquid product (or pyro-oil) was characterized by different ASTM standard methods to evaluate the fuel properties. Finally, fuel was used at 10 and 20% blending with commercial diesel to analysis the engine performance, combustion and emission at varying brake mean effective pressure and compression ratio. The results revealed that blending of PO reduces brake specific fuel consumption (BSFC) to achieve the same power. Comparing with commercial diesel, the blended fuels showed better brake power, brake thermal efficiency, mechanical efficiency, cylinder pressure, net heat release rate, and exhaust gas emission. An enhancement in BTE and ME with increasing in BMEP was observed and varies in the range of ∼ 0–34% and ∼ 0–95%, respectively. The blending of PO significantly reduces the emissions of CO, CO2, NOx and un-burnt hydrocarbon as well as improved the O2 emission. Reduced CO emission means a better lifestyle as the health risks factor is also reduced because inhalation of CO can form carboxyhemoglobin (COHb or HbCO) by dissolving in hemoglobin and restrict the oxygen circulation from lungs to the tissues that causes several health issues including death of a person.

English Else
Exergetic performance optimization and thermoeconomic analysis of a variable compression ratio diesel engine fueled with distilled plastic oil and diesel doped with nanographene

Amar Kumar Das,Taraprasad Mohapatra

DOI: https://doi.org/10.1177/09544089241229563

2024-02-10

Proceedings of the Institution of Mechanical Engineers Part E Journal of Process Mechanical Engineering

Abstract:Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, Ahead of Print. Due to the fast depletion of fossil fuels, enormous concerns about environmental pollution, and advocacy for waste-to-energy drives from the global perspective, compression ignition engines need a sustainable alternative fuel source. Enormous plastic wastes were generated in health sectors, particularly during post-pandemic. In this context, the study intends to introduce a reasonable solution for such waste plastics recycling by converting them into liquid oil by pyrolysis followed by the distillation process. Distilled waste plastic oil (DPO) extracted from medical plastic waste is a potential alternative diesel source. The performance of the engine significantly increases when nanographene is added with DPO/diesel blends, which act as a combustion improviser. The energy efficiency (η1), exergy efficiency (η2), and brake-specific fuel consumption (BSFC), which are regarded as key performance indicators, exhibited promising results when operated with 20% DPO +100 ppm nanographene (20DPO100G) emulsified fuel mixture as compared to normal diesel. When compared to diesel and other fuel combinations, the energy efficiency (η1) and exergy efficiency (η2) for 20DPO100G fuel mixture were found enhanced by 5.78% and 10.9%, respectively, and lowest by 14.7% for BSFC in comparison to diesel. The optimum energy efficiency, exergy efficiency, and minimum BSFC were obtained for the test engine from response surface methodology multi-objective optimization analysis as 31.44%, 22.12%, and 0.32 kg/kW-hr, respectively, for the composite desirability, D of 0.974. The 100 ppm nanographene emulsified distilled waste plastic pyrolysis oil and diesel blend has the lowest relative cost variation of −14.583.

engineering, mechanical
Processing and utilization of the solid plastic waste oil as the sustainable substitute for fossil fuel for the CI engine from microwave assisted pyrolysis process

Bingchao Zhao,Han Wang,Zikun Yao,Saleh Alfarraj,Sulaiman Ali Alharbi,Ramakrishnan Krishnan,Nguyen Thuy Lan Chi,Kathirvel Brindhadevi

DOI: https://doi.org/10.1016/j.fuel.2022.125191

IF: 7.4

2022-07-15

Fuel

Abstract:The fossil fuel crisis can be effectively tackled by the use of alternative fuels. Among the variety of biofuels, production of the biodiesel from the plastic waste seems much more attractive. Conversion of plastic waste into sustainable biodiesel plays a major role in combating the serious concern over the depletion of fossil fuels. The current research paper deals and explores the production of biodiesel from pyrolysis and transesterification method. Further the procured biodiesel was tested for performance and emission characteristics by varying the engines load. Microwave assisted pyrolysis process has been used to for obtaining the bio-oil from the plastic waste. All experimental tests were conducted in a naturally aspirated-inline, direct injection diesel engine at different engine speeds at constant load condition. The performance of the engine measured via Brake Power (BP), Brake Torque (BT), Brake Thermal Efficiency (BTE) and the emission are calculated via Carbon monoxide (CO), Carbon dioxide (CO 2 ) and Nitrogen oxide (NO). Each test blends WPO10, WPO20 and WPO30 were tested for the above parameters at the engine speed of 1000 rpm to 3000 rpm. All the procured results were comparatively examined with neat diesel. From the results, it is found that the brake power, brake torque and brake thermal efficiency were little lower for all taken blends compared to pure diesel. However, the major problem of emitting CO was considerably reduced while using plastic fuel blends. The CO 2 and NO emission were increased. There is no evidence of increase in the thermal efficiency due to the lower calorific value of the pyrolysis oil. Further, the viscosity and the poor presence of oxygen molecules reduced the overall combustion process which leads to high emission rates.

energy & fuels,engineering, chemical

Emergent Phenomena and Computer Worlds

Evaluation of Waste Plastic Pyrolysis Oil Performance with Diethyl Ether Additive on Insulated Piston Diesel Engine

Extraction and characterization of waste plastic pyrolysis oil for diesel engines

An experimental assessment on a diesel engine powered by blends of waste-plastic-derived pyrolysis oil with diesel

Performance, Combustion, and Emission analysis of diesel engine fuelled with pyrolysis oil blends and n-propyl alcohol-RSM optimization and ML modelling

Environmental impact of waste plastic pyrolysis oil on insulated piston diesel engine with methoxyethyl acetate additive

Experimental investigation to identify the type of waste plastic pyrolysis oil suitable for conversion to diesel engine fuel

Plastic pyrolytic oils as renewable fuel: improving its physical properties and ignition patterns by waste renewable source—an experimental analysis

Energy recovery of waste plastics into diesel fuel with ethanol and ethoxy ethyl acetate additives on circular economy strategy

Extraction and Performance Analysis of Hydrocarbons from Waste Plastic Using the Pyrolysis Process

Optimisation of an experimental and feasibility research on a CRDI diesel engine based on a blend of waste cooking oil and waste plastic oil using RSM: A value addition for disposed waste oil

Experimental Evaluation of Performance and Combustion Characteristics of Blended Plastic Pyrolysis Oil in Enhanced Diesel Engine

Waste plastic to pyrolytic oil and its utilization in CI engine: Performance analysis and combustion characteristics

Effective utilization of waste plastic derived fuel in CI engine using multi objective optimization through RSM

Optimisation of Process Parameters to Maximise the Oil Yield from Pyrolysis of Mixed Waste Plastics

Critical insights into the effects of plastic pyrolysis oil on emission and performance characteristics of CI engine

Experimental investigation of fuel injection timing effects on a CRDI diesel engine running on hydrogen-enriched waste plastic oil

Experimental Investigation in Compression Ratio on Performance, Combustion and Emission of VCR Engine using Pyrolysis-oil Produced from Waste Plastic Materials

Exergetic performance optimization and thermoeconomic analysis of a variable compression ratio diesel engine fueled with distilled plastic oil and diesel doped with nanographene

Processing and utilization of the solid plastic waste oil as the sustainable substitute for fossil fuel for the CI engine from microwave assisted pyrolysis process