Abstract:The utilization of plastic solid wastes for sustainable energy production is a crucial aspect of the circular economy. This study focuses on pyrolysis as an effective method to convert this feedstock into renewable drop-in fuel. To achieve this, it is essential to have a comprehensive understanding of feedstock composition, pyrolysis process parameters, and the physicochemical characteristics of the resulting fuel, all correlated with engine combustion parameters. Considering this full value chain, this study provides the first unbiased and up-to-date benchmark of polypropylene and polystyrene pyrolysis oils (PPO and PSO) produced in an industrial-grade batch reactor. The pyrolysis process was optimized to achieve ultra-high liquid yield levels of 92% for PPO and 98% for PSO with minimum energy consumption. After post-processing, blending with diesel, and normative fuel analytics, combustion/emission tests involving 20 species preceded under fully controllable conditions using a state-of-the-art single-cylinder research engine. The fuel analysis results revealed significant disparities between the properties of PPO and PSO. PPO exhibited a diverse carbon structure, resulting in very low density and high volatility. On the other hand, PSO was predominantly composed of aromatics, leading to low viscosity and poor auto-ignition properties. Engine tests showed that PPO blends exhibited combustion characteristics similar to diesel, while PSO blends exhibited significant differences, particularly during the premixed combustion stage attributed to pilot injection . Following the combustion response, the addition of PPO had minimal impact on emissions, while PSO acted as an emission enhancer, resulting in over twofold increase in particulate matter at high loads. Consequently, PSO showed elevated carbon monoxide and hydrocarbon emissions due to the higher contribution of aromatics. Ultimately, this study challenges the prevailing perception of plastic-derived fuels as "dirty". By implementing feedstock segregation to minimize polystyrene content, it is possible to achieve a fossil substitute level of 40% while meeting all emission and safety regulations for diesel engines with a minimum economic burden.

Evaluating the properties of a novel diesel-like fuel produced by biochar-assisted catalytic cracking of waste motor oil

Investigation on Thermal Properties of a Novel Fuel Blend and Its Diesel Engine Performance

Kinetic study of the catalytic cracking of waste motor oil using biomass-derived heterogeneous catalysts

Enhancing the conversion of waste motor oil into diesel-like fuels using mineral-impregnated biochar catalysts

Production of diesel-like fuel by catalytic co-pyrolysis of waste cooking oil and waste lubricating oil—an alternate energy source

Investigating Engine Performance and Emission Characteristics of a CI Engine Fueled with Waste Fried Oil Blend Containing Butanol, Alumina, and Silver Nanoparticles

Techno-economic and life cycle assessment of renewable diesel production via methane-assisted catalytic waste cooking oil upgrading

Diesel Production via Standalone and Co-Hydrotreating of Catalytic Fast Pyrolysis Oil

Renewable biocrude blends boost tribological properties and maintain fuel performance of diesel

An experimental assessment on a diesel engine powered by blends of waste-plastic-derived pyrolysis oil with diesel

Potential of Fatty Acid Methyl Ester as Diesel Blends Produced from Free Fatty Acid in Waste Cooking Oil Catalyzed by Montmorillonite-Sulfonated Carbon

Novel Diesel-Like Liquid Fuel Production by Hydrodeoxygenation–In Situ Esterification of Lignin-Derived Bio-oil and Plant/Animal Oil

Engine behavior analysis on a conventional diesel engine combustion mode powered by low viscous cedarwood oil/waste cooking oil biodiesel/diesel fuel mixture – An experimental study

Application of waste derived magnetic acid-base bifunctional CoFe/biochar/CaO as an efficient catalyst for biodiesel production from waste cooking oil

Investigation of Novel Transition Metal Loaded Hydrochar Catalyst Synthesized from Waste Biomass (Rice Husk) and Its Application in Biodiesel Production Using Waste Cooking Oil (WCO)

Experimental investigation and optimization of dual fuel combustion using diesel/gasoline and Bio-oil extracted from Co-thermal liquefaction of paint/biomass wastes: An approach towards waste to energy

Biodiesel Production from Waste Frying Oil (WFO) Using a Biomass Ash-Based Catalyst

Recent Progress in the Development of Biofuel 2,5-Dimethylfuran.

Production of biofuel from AD digestate waste and their combustion characteristics in a low-speed diesel engine

Characterisation of Waste Derived Intermediate Pyrolysis Oils for Use As Diesel Engine Fuels

Characterization of the Lubricity of Bio-Oil/diesel Fuel Blends by High Frequency Reciprocating Test Rig