Abstract:The joining of glass and Mg by a combination of anodic bonding and vacuum diffusion bonding with Al as the interlayer was achieved in one step. The microstructures of glass/Mg dissimilar joints were analyzed using optical microscopy, SEM, and EDS. The results show that the bonding interface was joined well without any voids and cracks. Na + and Ca 2+ depletion regions would be produced in the glass near the Al foil, where the width of the Na + depletion region was larger than that of the Ca 2+ depletion region. In addition, the content of Al element in the depletion regions increased, and the diffusion of Al into the depletion regions was responsible for the successful glass/Al bonding process. Al 3 Mg 2 and Al 12 Mg 17 intermetallic compound (IMC) layers were formed between the Al and Mg. The anodic bonding process and the vacuum diffusion bonding process were independent of each other: and the thickness of the IMC layer increased with the increase of the diffusion bonding time, while the width of the Na + , Ca 2+ depletion region remained constant; Meanwhile, the variation of the anodic bonding parameters only affected the width of the depletion layer and had no effect on the thickness of the Al 3 Mg 2 and the Al 12 Mg 17 IMC layer. The fracture position of the sample changed from the Al/Mg bonding interface to the glass/Al bonding interface as the thickness of the IMC layer increased. The maximum tensile strength of 14.6 MPa was obtained by vacuum diffusion bonding at 450 °C for 20 min and anodic bonding under 400 °C and 800 V.

Interfacial evolution mechanism of MgAl2O4/MgAl2O4 joints bonded with lanthanum glass

Microstructure, mechanical and optical properties of MgAl2O4/MgAl2O4 joints bonded using CaO-Al2O3-SiO2 glass filler

Joining MgAl2O4 ceramics using ZnO–Al2O3–SiO2 glass ceramic with precipitated ZnAl2O4

Microstructure evolution and cooperative reinforcement mechanisms of Al2O3/Al2O3 joints brazed by low-melting borosilicate glass

Research on the interfacial microstructure and mechanical properties of glass/Mg joint prepared by anodic bonding and vacuum diffusion bonding

Microstructure and Strength of Al2o3/Al2o3 Joints Bonded with Zno-Al2o3-B2o3-Sio2 Glass-Ceramic

Joining Dense Si3N4 to Porous Si3N4 Using a Novel Glass-Ceramic Interlayer with Precipitated Β-Lialsi2o6/mg2sio4

Novel design of sapphire/spinel transparent ceramic joints with double glass interlayers by coating and bonding

Effects of Glass Composition and Joining Parameters on Microstructural Evolution and Mechanical Properties of Al2O3/Cu Joints Brazed with Bi2O3-B2O3-ZnO Glass

Microstructure and Properties of Porous Si3N4/Dense Si3N4 Joints Bonded Using RE–Si–Al–O–N (RE = Y or Yb) Glasses

Influence of Al Interlayer Thickness on Laser Welding of Mg/Steel

Microstructure Evolution and Mechanical Properties of Znal2o4-Reinforced Al2o3/Al2o3 Joints Brazed with A Bismuth Borate Zinc Glass

Microstructure Evolution and Mechanical Properties of Porous Si3N4 and Dense Si3N4 Joints Bonded Using CaO–Li2O-Al2O3–SiO2 Glass-Ceramic

Microstructure Evolution During Air Bonding of Al2O3 to Al2O3 Joints Using Bismuth–borate–zinc Glass

Joining of Porous Alumina with a CaO–Al2O3–SiO2 Glass‐Ceramic

Crystallization Behavior of Glass Ceramic Filler During Joining Process

Low-temperature Brazing of Alumina Ceramics with Bismuth-Borate Glass in Air

Joining high volume fraction SiC particle reinforced aluminum matrix composites using Bi2O3-B2O3-ZnO-BaO-Na2O glass

Joining Mg Alloys with Zn Interlayer by Novel Ultrasonic-Assisted Transient Liquid Phase Bonding Method in Air

Joining of Al2O3 to ZTA Using a B2O3–Al2O3–SiO2 Glass with In-Situ Precipitated Whiskers

Regulating the Glass Network Structure of SiO2f/SiO2 Composite Joints by In-Situ Silica Diffusion