Abstract:Organometal halide perovskite is one of the most promising materials for high efficient thin-film solar cell. Solution fabrication process shows that the recorded power conversion efficiency (PCE) is 23.7%, however, large scale fabrication suffers the inevitable toxic solvent, preventing it from implementing the green commercialization. As one of the matured large-scale fabrication techniques, the vapor deposition is recently found to promise the green fabrication of perovskite thin film without toxic solvent. However, the PCE based on vapor deposition is considerably lower than that based on solution fabrication because of ineffective regulation methods of the perovskite films. So, there is intensive requirement for optimizing the growth of perovskite in vapor deposition for improving PCE, especially, developing a kind of quality regulation method of the perovskite films. In this study, we provide a method of adjusting grain size in vapor deposition method. The grain size optimization of MAPbI 3 films is realized by simply modulating the reaction temperature between PbI 2 films and MAI vapor. We set the reaction temperature to be 140 °C, 160 °C, 180 °C and 200 °C separately and establish the relationship between reaction time and grain size during the complete conversion of PbI 2 film into MAPbI 3 film. We find that the average grain size of the film increases first with growth temperature increasing from 140 °C to 180 °C and then decrease at 200 °C, giving an average grain size of 0.81 \begin{document}${\text{μm}}$\end{document} and a largest grain size of about 2 \begin{document}${\text{μm}}$\end{document} at 180 °C. The defect density of perovskite film is deduced from the space charge limited current model, showing that it decreases from 5.90 × 10 16 cm –3 at 140 °C to 2.66 × 10 16 cm –3 at 180 °C. Photovoltaic devices with structure FTO/TiO 2 /C 60 /MAPbI 3 /spiro-OMeTAD/Au are fabricated to demonstrate the performance. It is found that the devices with an active area of 0.045 cm 2 show that with the increase of grain size, the average PCE increases from 14.00% to 17.42%, and the best device shows that its PCE is 17.80% with 4.04% hysteresis index. To show the possibility of scaling up, we fabricate a uniform perovskite thin film with an area of about 72 cm 2 , and a device with an active area of 1 cm 2 , which gives a PCE of 13.17% in reverse scan. In summary, our research provides a method of regulating the grain size for the vapor deposition, which can improve device performance by reducing the trap density in perovskite film for suppressing the carrier recombination in grain boundary. Meanwhile, we prepare high performance devices and large area thin films, showing their potential in large area device fabrication and applications.

Impact of Ternary Solvent on the Grain Size and Defects of Perovskite Layer to Realize a Stable Morphology for Efficient Inverted Solar Cells

A Polymerization‐Assisted Grain Growth Strategy for Efficient and Stable Perovskite Solar Cells

Improving stability and efficiency of three-dimensional perovskite solar cells with organophosphorus ligands

Morphology Optimization of Perovskite Films for Efficient Cells and Modules through Solvent Engineering

(Invited) Improvement of Perovskite Films and the Perovskite/TiO2Interface

Impact of Solvent Additive on Morphology of High-Efficiency Ternary Blend Solar Cell

Realization of Moisture-Resistive Perovskite Films for Highly Efficient Solar Cells Using Molecule Incorporation

Reducing surficial and interfacial defects by thiocyanate ionic liquid additive and ammonium formate passivator for efficient and stable perovskite solar cells

In Situ Polymerization of Cross‐Linked Perovskite–Polymer Composites for Highly Stable and Efficient Perovskite Solar Cells

CH 3 NH 3 PbBr 3– x I x Quantum Dots Enhance Bulk Crystallization and Interface Charge Transfer for Efficient and Stable Perovskite Solar Cells

The Effects of Solvent on Doctor‐Bladed Perovskite Light Absorber under Ambient Process Condition for Multiple‐Cation Mixed Halide Perovskites

Morphology Control towards Green Solvent System Processed High Performance Semitransparent CH3NH3PbI3 Film for Perovskite Solar Cell

Enhancing the Stability and Efficiency of Inverted Perovskite Solar Cells with a Mixed Ammonium Ligands Passivation Strategy

A Thermotropic Liquid Crystal Enables Efficient and Stable Perovskite Solar Modules

Synergistic Interface Layer Optimization and Surface Passivation with Fluorocarbon Molecules toward Efficient and Stable Inverted Planar Perovskite Solar Cells

Optimization of grain size to achieve high-performance perovskite solar cells in vapor deposition

Managing Interfacial Defects and Carriers by Synergistic Modulation of Functional Groups and Spatial Conformation for High‐Performance Perovskite Photovoltaics based on Vacuum Flash Method

Improvement of Cs-(FAPbI(3))(0.85)(MAPbBr(3))(0.15) Quality Via DMSO-Molecule-Control to Increase the Efficiency and Boost the Long-Term Stability of 1cm(2) Sized Planar Perovskite Solar Cells

Surface Reconstruction for Efficient and Stable Monolithic Perovskite/Silicon Tandem Solar Cells with Greatly Suppressed Residual Strain

Effect of Co‐Solvents on the Crystallization and Phase Distribution of Mixed‐Dimensional Perovskites

Controllable Grain Morphology Of Perovskite Absorber Film By Molecular Self-Assembly Toward Efficient Solar Cell Exceeding 17%