Abstract:Charge accumulation and charged defects at both bulk and buried heterojunction interfaces of perovskites are primarily related to the photovoltaic performance and shelf stability of perovskite solar cells (PSCs). Moreover, detrimental defects distributing along the perovskite bottom side in contact with the tin oxide (SnO2) surface may exert unparalleled significance in charge extraction and transport. Most importantly, interfacial nonradiative recombination can also widely exist, which will seriously hamper efficiency of the related device. In this work, a multifunctional chemical bridge at the perovskite/SnO2 interface is devised through triggering an in situ polymerization strategy, by which cross-linked polymerizable 3-(trimethoxysilyl)propyl methacrylate (MAPS) monomers under the combination of temperature and initiators can form bulkier macropolymers (MAPS dimers). Detailed theoretical and experimental results reveal that the carbonyl groups (CO) of both MAPS monomers and MAPS dimers can chemically anchor to perovskite bottom side through a CO···Pb coordination bond interaction to regulate the film quality and the siloxane groups effectively couple with oxygen vacancies on the SnO2 film surface to facilitate its optoelectronic properties. Compared with the primitive MAPS monomer units, the resultant MAPS dimers simultaneously prevent interfacial charge accumulation and demonstrate a more benign energy level alignment to further augment photovoltaic performance of PSCs. Thus, the devices assembled under open-air conditions based on double-sided passivation deliver a decent photoelectronic performance with the champion efficiency of 20.94% accompanied by negligible hysteresis. Meanwhile, the unencapsulated targeted devices maintain 93.1% and 86.5% of their original efficiency after continuous 500 h thermal treatment and 500 h light illumination under open-circuit conditions, respectively.

In Situ Polymerization of Cross‐Linked Perovskite–Polymer Composites for Highly Stable and Efficient Perovskite Solar Cells

Enhanced Crystallization and Optimized Morphology of Perovskite through Doping Indium-Based Metal-Organic Assembly: Achieving Significant Solar Cell Efficiency Enhancements

A Polymerization‐Assisted Grain Growth Strategy for Efficient and Stable Perovskite Solar Cells

Bifunctional Modified Biopolymer for Highly Efficient and Stable Perovskite Solar Cells and Modules

Macromonomer Crosslinking Polymerized Scaffolds for Mechanically Robust and Flexible Perovskite Solar Cells

Fabrication of stable perovskite solar cells with efficiency over 20% in open air using <i>in situ</i> polymerized bi-functional additives

Unified Crystal Phase Control with MACl for Inducing Single‐Crystal‐Like Perovskite Thin Films in High‐Pressure Fusion Toward High Efficiency Perovskite Solar Cell Modules

Realizing Stable Perovskite Solar Cells with Efficiency Exceeding 25.6% Through Crystallization Kinetics and Spatial Orientation Regulation

Enhancing the Stability and Efficiency of Inverted Perovskite Solar Cells with a Mixed Ammonium Ligands Passivation Strategy

Self‐Polymerization of Monomer and Induced Interactions with Perovskite for Highly Performed and Stable Perovskite Solar Cells

Grain engineering by ultrasonic substrate vibration post-treatment of wet perovskite films for annealing-free, high performance, and stable perovskite solar cells.

Acetic Acid Assisted Crystallization Strategy for High Efficiency and Long-Term Stable Perovskite Solar Cell

Simultaneous Interface Amelioration and Energy Level Modulation Using In Situ Polymerized Molecules for Efficient and Stable Perovskite Solar Cells

Efficient and Stable Perovskite Solar Cell Achieved with Bifunctional Interfacial Layers.

Polymer-templated nucleation and crystal growth of perovskite films for solar cells with efficiency greater than 21%

Grain Boundary Chemical Anchoring via Bidirectional Active Site Additive Enables Efficient and Stable Perovskite Solar Cells

Efficient Passivation with Lead Pyridine‐2‐Carboxylic for High‐Performance and Stable Perovskite Solar Cells

Controlled Nucleation and Oriented Crystallization of Methylammonium‐Free Perovskites via In‐Situ Generated 2D Perovskite Phases

A-site Assisted Perovskite Crystallization Via Ion-Exchange MOFs for High Efficient and Stable Perovskite Solar Cells

Heterogeneous Nucleation and Enhanced Charge Transfer via Amorphous Metal‐Organic Frameworks for Efficient and Stable Perovskite Solar Cells

Stable perovskite solar cells with 25.17% efficiency enabled by improving crystallization and passivating defects synergistically