Abstract:Purpose The curved and tribologically highly stressed surfaces of bearing components pose a major challenge for steel alloys or tribological resistant coatings like tetrahedral amorphous carbon (ta-C) coatings which in particular have an increased risk of delamination due to the significantly increased residual stresses. A possibility to prevent coating failure is the use of dopants while maintaining or even increasing tribological properties. This study aims to compare the tribological behavior of several doped diamond-like-carbon coatings with an undoped ta-C coating under varying slip conditions and Hertzian pressure up to 1800 MPa. Design/methodology/approach For this purpose, the tribological behavior was studied using of a ball-on-disc tribometer and a two-disc test rig under mixed/boundary conditions. The tests were conducted with coated specimens against uncoated 100Cr6 steel. Additionally, the influence of lubrication additives was studied due to the use of two fully formulated PAO-based oils, one without and one with molybdenum containing additives. The friction was measured in situ, and the wear was analyzed trough laser scanning microscopy and tactile measurement. Findings It was shown that the use of doped ta-C coatings exhibited a tendency for a more favorable tribological behavior compared to undoped ta-C coatings, with no general dependence on the lubricants used. The use of the most suitable coatings reduced the wear of the steel counter-body considerably. Originality/value To the best of the authors' knowledge, this is the first approach of testing the tribological behavior of these doped ta-C coatings, developed for friction efficiency, in dependency on lubrication additives under the given load collective. The approach is relevant to determine whether the friction reduction and the wear inhibition of these coatings are suitable for higher contact pressures and load cycles. Peer review The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-11-2022-0336/

Comparative tribological performance of a-C:H, ta-C and AlCrSiN coatings on 20CrMnTi gear steel under dry sliding condition

Tribological behavior of different doped ta-C coatings for slip-rolling contacts with high hertzian contact pressure

High-temperature tribological properties of AlCrN coatings deposited on textured surfaces under dry friction

Scuffing Resistance of 16MnCr5 HCR TiAlCN-Coated Gears

The Tribological Performance of Surface Treated Ti6A14V as Sliding Against Si3N4 Ball and 316L Stainless Steel Cylinder

Tribological behaviour of TiAlN and AlCrN coatings on stainless steel

Preparation and Performance of a Cr/CrN/TiAlCN Composite Coating on a GCr15 Bearing Steel Surface

Coordinating influence of multilayer graphene and spherical SnAgCu for improving tribological properties of a 20CrMnTi material

Growth, mechanical properties, and tribological performance of TiAlN/NbN and NbN/TiAlN bilayer coatings

A comparative analysis of different surface tribological and electrochemical properties of TiAlN, TiAlSiN, and CrAlN thin film coatings in seawater

Tribological performance of Mn3(PO4)2 coating and PC/MoS2 coating in Rolling–Sliding and pure sliding contacts with gear oil

Structure and Tribological Properties of CrTiAlCN Coatings with Various Carbon Contents

Tribological Dependence of the High-Performance Ferrous-Based Coating on Different Coating Counterparts in Engine Oil

Additional Tribological Effect of Laser Surface Texturing and Diamond-Like Carbon Coating for Medium Carbon Steel at Near Room Temperature

Tribological Properties of Craln and Tin Coatings Tested in Nano- and Micro-Scale Laboratory Wear Tests

Wear of AlCrN and CrAlSiN Coatings Applied to Nonstandard Involute Gears

Interesting ' island-like' microstructure and tribological evaluation of Al 1.5 CrFeNiWTi 0.5 high entropy alloy coating manufactured by laser cladding

Tribological Properties and Preparation of (Ti,Al)N Coatings on High Speed Steel Substrate

Tribological performance of GLC, WC/GLC and TiN films on the carburized M50NiL steel

The Tribological Behaviors of Three Films Coated on Biomedical Titanium Alloy by Chemical Vapor Deposition