Abstract:Superior properties of titanium alloy Ti-6Al-4V over many other materials like higher strength to weight ratio, ability to maintain strength at elevated temperatures (around 500 degrees C) and ability to resist against corrosion in severe environmental conditions have made them as an excellent choice for using them in many aerospace and biomedical industrial applications. But the properties which had made them an ideal choice for most practical applications severely hinders their machinability and therefore is renowned as difficult to machine material. The low thermal conductivity of titanium alloys does not allow the generated heat to dissipate away quickly and thus results in chemical reaction with cutting tool materials at higher temperatures. Several researchers have tried to reduce tool-chip interface temperature, increase tool life and surface quality with carbide tools by applying different cutting fluids like water based emulsions flood cooling, oil flood coolant, minimum quantity lubrication MQL and various liquid nitrogen LiN cryogenic cooling techniques and has found some advantages of MQL & LiN cooling in terms of not only in improved surface roughness & tool life but also in controlling the hazardous environmental impact by eliminating the use of hazardous and expensive traditional flood coolant equipment. Moreover the thrust for higher quality and productivity has directed the attention of researchers on using super hard cutting tool materials for machining of titanium alloys. Super hard cutting tool like polycrystalline diamond PCD, Poly Cubic Boron Nitride PCBN and Binderless CBN inspite of their higher cost has many advantages over carbide tools like higher thermal conductivity, lower wear rate and high hot strength. Studies have shown that PCD tools can give better tool life and surface roughness as compared to carbide and PCBN tools. The studies on evaluating the effectiveness of PCD insert in high speed end milling of titanium alloy has not yet considered the effect of different types of cooling strategies. Therefore there is need to study the effectiveness of PCD tools in various wet cutting conditions and find optimal coolant which can help to increase tool life and can provide better surface quality and therefore this study is specifically designed to address above mentioned issues. Four different type of coolants "water based flood cooling, oil based flood coolant, MQL and LIN cryogenic cooling technique has been applied and their effect on tool-chip interface temperature, tool edge temperature, cutting forces and stresses acting on tool edge are observed using Finite element, FE numerical simulations. FE numerical simulations are widely employed in academic research field because it provides fast & reliable results and thus eliminates expensive experimentation costs which otherwise is always required. Results have shown that the LiN cooling technique has shown clear advantages over MQL and flood coolant techniques in terms of temperature near the tool rake face and in reducing cutting forces and stresses acting on cutting edge. Therefore from the study it can be concluded that LiN cooling can be used for machining of titanium alloys with PCD inserts for getting maximum productivity and part quality.

Comparative analysis of the cutting performances of SiAlON ceramic, cubic boron nitride and carbide cutting tools for titanium machining

Comparative investigation and optimization of cutting tools performance during milling machining of titanium alloy (Ti6Al4V) using response surface methodology

Influence of Tool Geometrical Parameters on High Speed Cutting of Titanium Alloy Ti6Al4V

Comparative performance evaluation between ta-C and TiAlCrN coated tools during milling of additively manufactured CFRP composite

Comparative analysis over microstructural, mechanical properties and cutting performance of TiN, TiVN coatings deposited by magnetron sputtering on SiAlON ceramic tool insert

Evaluating the Effectiveness of Various Coating Layers Applied on K-Grade Cemented Carbide Cutting Tools on Machinability of Titanium Alloy Ti-6Al-4V in High Speed End Milling

Evaluation of specific cutting energy, tool wear, and surface roughness in dry turning of titanium grade 3 alloy

Evaluating the Effectiveness of PCD Tools on Machinability of Titanium Alloy Ti-6Al-4V in High Speed End Milling under Various Wet Cutting Conditions

Study on the Orthogonal Cutting Process of Al7050T7451 with Uncoated and Coated Tools

Optimization of Process Parameters to Achieve Reduced Tool Wear and Increased Tool Life Using Alumina Based Ceramic Cutting Tools in Milling

Comparative experimental study on application feasibiility of MTCVD TiCN-Al2O3-TiOCN multi-layer coated carbide and PVD TiN single layer coated composite ceramic inserts during dry machining of Ti-6Al-4V

A Comparative Experimental Study on Machining Performance of Aluminium against Advanced Diamond Coated Cutting Tool Inserts

Machinability Performance of Single Coated and Multicoated Carbide Tools During Turning Ti6Al4V Alloy

Study of a Novel Ceramic Tool Performance in the Machining of Ti-6Al-7Nb Alloys

Machinability Comparison of TiCN-Al2O3-TiN, TiAlN-TiN, and TiAlSiN Coated Carbide Inserts in Turning Hardened AISI 4340 Steel Using Grey-Crow Search Hybrid Optimization

The performance of advanced cutting tools used for dry machining of aluminium

Finite element analysis of Ti 1-x Al x N coated tools cutting performance and tool wear during Ti-6Al-4V milling

An Investigation of the Effect of Novel Mono/Bi-Layered PVD-Coated WC Tools on the Machinability of Ti-5Al-5V-5Mo-3Cr

Investigating drilling efficiency: a study on indexable centerless drilling of Ti-6Al-4 V alloy

Experimental investigation of cutting forces in dry grinding of Ti-6Al-4V alloy using CNT nano grinding tool

Effect of Surface-Textured AlSiTiN Coating Parameters on the Performance of Ball-End Milling Cutter in Titanium Alloy Milling