Abstract:Superior properties of titanium alloy Ti-6Al-4V over many other materials like higher strength to weight ratio, ability to maintain strength at elevated temperatures (around 500 degrees C) and ability to resist against corrosion in severe environmental conditions have made them as an excellent choice for using them in many aerospace and biomedical industrial applications. But the properties which had made them an ideal choice for most practical applications severely hinders their machinability and therefore is renowned as difficult to machine material. The low thermal conductivity of titanium alloys does not allow the generated heat to dissipate away quickly and thus results in chemical reaction with cutting tool materials at higher temperatures. Several researchers have tried to reduce tool-chip interface temperature, increase tool life and surface quality with carbide tools by applying different cutting fluids like water based emulsions flood cooling, oil flood coolant, minimum quantity lubrication MQL and various liquid nitrogen LiN cryogenic cooling techniques and has found some advantages of MQL & LiN cooling in terms of not only in improved surface roughness & tool life but also in controlling the hazardous environmental impact by eliminating the use of hazardous and expensive traditional flood coolant equipment. Moreover the thrust for higher quality and productivity has directed the attention of researchers on using super hard cutting tool materials for machining of titanium alloys. Super hard cutting tool like polycrystalline diamond PCD, Poly Cubic Boron Nitride PCBN and Binderless CBN inspite of their higher cost has many advantages over carbide tools like higher thermal conductivity, lower wear rate and high hot strength. Studies have shown that PCD tools can give better tool life and surface roughness as compared to carbide and PCBN tools. The studies on evaluating the effectiveness of PCD insert in high speed end milling of titanium alloy has not yet considered the effect of different types of cooling strategies. Therefore there is need to study the effectiveness of PCD tools in various wet cutting conditions and find optimal coolant which can help to increase tool life and can provide better surface quality and therefore this study is specifically designed to address above mentioned issues. Four different type of coolants "water based flood cooling, oil based flood coolant, MQL and LIN cryogenic cooling technique has been applied and their effect on tool-chip interface temperature, tool edge temperature, cutting forces and stresses acting on tool edge are observed using Finite element, FE numerical simulations. FE numerical simulations are widely employed in academic research field because it provides fast & reliable results and thus eliminates expensive experimentation costs which otherwise is always required. Results have shown that the LiN cooling technique has shown clear advantages over MQL and flood coolant techniques in terms of temperature near the tool rake face and in reducing cutting forces and stresses acting on cutting edge. Therefore from the study it can be concluded that LiN cooling can be used for machining of titanium alloys with PCD inserts for getting maximum productivity and part quality.

Optimization of Process Parameters to Achieve Reduced Tool Wear and Increased Tool Life Using Alumina Based Ceramic Cutting Tools in Milling

Comparative investigation and optimization of cutting tools performance during milling machining of titanium alloy (Ti6Al4V) using response surface methodology

Machining parameter optimization for face milling operating in a vertical CNC milling machine using Taguchi design approach

Optimization of machining parameters for turning operation of heat-treated Ti-6Al-3Mo-2Nb-2Sn-2Zr-1.5Cr alloy by Taguchi method

Effect of Surface-Textured AlSiTiN Coating Parameters on the Performance of Ball-End Milling Cutter in Titanium Alloy Milling

Comparative analysis of the cutting performances of SiAlON ceramic, cubic boron nitride and carbide cutting tools for titanium machining

Optimizing machining efficiency: a comprehensive study on PVD cathodic arc evaporation coated turning tool inserts with TiAlN/AlCrN multilayer coatings

Tool Life Prediction of Ti [C,N] Mixed Alumina Ceramic Cutting Tool Using Gradient Descent Algorithm on Machining Martensitic Stainless Steel

Evaluating the Effectiveness of PCD Tools on Machinability of Titanium Alloy Ti-6Al-4V in High Speed End Milling under Various Wet Cutting Conditions

Multi-Objective Optimization of Micro-Milling Titanium Alloy Ti-3Al-2.5V (Grade 9) Using Taguchi-Grey Relation Integrated Approach

Optimizing the micro-texture and cutting parameters of ball-end milling cutters to achieve milling stability

The performance of advanced cutting tools used for dry machining of aluminium

Machinery parameter optimization of CNC milling programming towards process time

An experimental approach to characterize the performance of PCD and PCBN tools in milling nano Al-8081-Zr/Mg/TiO2 metal matrix composites using multi-sensor data fusion

Experimental Study on the Optimization of Ti1023 Milling Parameters

Research on cutting performance and tool life improvement methods of titanium alloy ultra-high speed milling tools

Experimental Optimization of Process Parameters for Turning TC11 Titanium Alloy Using Taguchi Methodology Design

Modeling and Optimization of Tool Wear and Surface Roughness in Turning of Al/SiCp Using Response Surface Methodology

Study of Wear, Stress and Vibration Characteristics of Silicon Carbide Tool Inserts and Nano Multi-Layered Titanium Nitride-Coated Cutting Tool Inserts in Turning of SS304 Steels

Parametric optimisation of milling process for the machining of carbon nanotubes-based hybrid aluminium composite

Experimental and 3D-Deform Finite Element Analysis on Tool Wear during Turning of Al-Si-Mg Alloy