Abstract:To date, the most commonly used aluminum alloys for additive manufacturing are eutectic/near-eutectic alloys. However, fabricating high strength aluminum parts has not yet been fully investigated due to solidification cracking and porosity formation, which make these alloys very hard to be processed. Electron beam selective melting (EBSM) of aluminum alloys has some advantages over selective laser melting. The process is not affected by reflectivity of aluminum powders, and parts exhibit less induced thermal stresses. In addition, oxidation is reduced due to vacuum condition. Therefore, the process provides high potential for the fabrication of aluminum alloys, specifically, Al2024 alloy which is widely used in different industries such as automotive and airline industries. Hence, these industries are highly benefitted from being able to build defect-free AM parts. This study is significant because Al2024 alloy is highly susceptible to solidification cracking and porosity formation, and crack-free samples with high relative densities have not been built by EBM process previously. The baseplate preheating temperature was set to 350 degrees C, and samples were fabricated by applying a proper powder bed preheating configuration for each layer. Different sets of processing parameters were used to investigate their effect on the performance of the parts. Archimedes technique was used to measure the relative density of samples, ranging from 95% to full-dense. The results showed that higher relative densities could be achieved by increasing the input energy to an optimum value; however, by further increasing the energy, the relative density decreases, which can be attributed to porosity formation. SEM and EBSD results showed equiaxed grains in a crack-free microstructure. Grain structure consisted of high angle grain boundaries having different crystallographic orientations with a few subgrains. Additionally, AlCuMnFe, AlCuMnFeSi, and eutectic Al2Cu phases were uniformly distributed in the alpha phase matrix. Microhardness results showed an almost uniform change of hardness values in both horizontal and vertical sections, ranging from 100 HV to 110 HV for as-built samples. Moreover, tensile and yield strengths of as-built samples reached 314 MPa and 191 MPa, respectively, which can be further increased by a proper post-processing treatment. (C) 2020 Elsevier B.V. All rights reserved.

Microstructural damage during electrical discharge machining of a high silicon aluminum alloy for space applications

Investigation on Surface Quality of a Rapidly Solidified Al-50%Si Alloy Component for Deep-Space Applications

Micro-EDM for an aluminium matrix composite

Die-sinking EDM of Al6061-T6: interactions between process parameters, process performance, and surface characteristics

Research on the Mechanism of Material Erosion of High Silicon Aluminum Alloy in Micro EDM

Studies on the Surface of High-Performance Alloys Machined by Micro-Edm

SEM-DIC characterization of the damage mechanism of an AlSi10Fe0.7 casting alloy on the microstructure scale

Residual stresses and surface damage when micromachining 6061-T6 aluminum alloy

Micro electrical discharge milling of a monocrystalline silicon complex micro-cavity

Electrical Discharge Machining of Al2024-65 Vol% Sic Composites

Electrical Discharge Machining of SiC Reinforced 6061-T6 Aluminum Alloy Surface Composite Fabricated by Friction Stir Processing

Electrical Discharge Machining of SiC and Gr Reinforced 6061-T6 Aluminum Alloy Hybrid Composite Fabricated by Friction Stir Processing

Selective electron beam melting of high strength Al2024 alloy; microstructural characterization and mechanical properties

Micro-scale measurement & FEM modelling of residual stresses in AA6082-T6 Al alloy generated by wire EDM cutting

Micro Electrical Discharge Machining Techniques of Semiconducting Silicon Material

Microstructural evolution caused by electromagnetic stirring in superheated AlSi7Mg alloys

Surface modification of aluminum alloy by wire electrical discharge machining with SiC nanofluid dielectric

Microhardness Distribution and Microstructural Evolution in Pure Aluminum Subjected to Severe Plastic Deformation: Elliptical Cross-Sectioned Spiral Equal-Channel Extrusion (ECSEE)

Microstructure, wear and residual stresses of selective laser melting AlSi10Mg solid cylinder

EDM Studies on Aluminum Alloy-Silicon Carbide Composites Developed by Vortex Technique and Pressure Die Casting

Experimental and numerical investigations into the fabrication of alumina ceramic surface microchannel by electrochemical discharge machining