Abstract:Additive manufacturing (AM) has gained popularity across various industries due to its cost-effectiveness, low material consumption, and minimal environmental impact. Localized electrochemical deposition (LECD), as one of the AM methods, has the capability to produce microcomponents or structures at an microscale in a specific position as designed, without the need for any mask or support material[1]. By reducing copper ions in the local area according to the position of the micro-wire, 3D structures could be produced. This electrochemical deposition process has a significant advantage in that it is a low-temperature process and has lower costs compared to other processes[2]. Using the LECD process, the micrometer of copper columns was conventionally deposited in copper sulfate-based electrolyte[3]. However, this electrolyte has the possibility to cause damage to the metal substrate used as the cathode due to its low pH, resulting in metal dissolution. The utilization of copper pyrophosphate-based electrolyte, which is a solution with a pH close to neutral, can solve this problem. Also, copper pyrophosphate-based electrolyte offers an advantage over conventional alkaline-based electrolytes in that it removes cyanide pollution of the environment and hazards to human health.[4] In this study, the microanode was employed using a platinum wire(100 μm in diameter), while a copper substrate was employed as the cathode in the electrochemical deposition process. The micrometer copper columns were deposited using copper pyrophosphate-based electrolyte by varying the main electrochemical deposition factors, such as applied potential and pulse duty cycle. In addition The surface morphology of the deposited micrometer-scale copper columns was observed through scanning electron microscopy. REFERENCES [1] Suryavanshi, Abhijit P., and Min-Feng Yu. "Probe-based electrochemical fabrication of freestanding Cu nanowire array." Applied Physics Letters 88.8 (2006): 083103. [2] Madden, John D., and Ian W. Hunter. "Three-dimensional microfabrication by localized electrochemical deposition." Journal of microelectromechanical systems 5.1 (1996): 24-32. [3] Lin, J. C., et al. "Localized electrochemical deposition of micrometer copper columns by pulse plating." Electrochimica Acta 55.6 (2010): 1888-1894. [4] Chen, C-C. "A New Process for Cyanide-Free Copper Plating." Electroplating and Pollution Control 23.4 (2003): 10-11.

Sugar‐Based Electroless Copper Deposition on Pectin‐Coated Alumina Microparticles

Maillard Type Reaction for Electroless Copper Plating onto Ceramic Nanoparticles

Study on a New Activation Method for Initiating Electroless Plating on Alumina Powders Based on SAMs Bonded Palladium

Copper metallization of carbon fiber-reinforced epoxy polymer composites by surface activation and electrodeposition

Electroless plating of copper on carbon fiber surfaces and corresponding mechanism

Copper Thin Coating Deposition on Natural Pollen Particles

Fabrication of Conductive Copper Patterns Using Photocatalyst-activated Electroless Deposition

Microstructure and properties of copper plating on citric acid modified cotton fabric

Emerging Non-Noble-Metal Atomic Layer Deposited Copper as Seeds for Electroless Copper Deposition

Localized Electrochemical Deposition Using Copper Pyrophosphate-Based Electrolyte

Preparation and Biochemical Activity of Copper-Coated Cellulose Nonwoven Fabric via Magnetron Sputtering and Alginate-Calcium Ion Complexation

One-Step Electrodeposition of Self-Assembled Colloidal Particles: A Novel Strategy for Biomedical Coating

Electrophoretic deposition of collagen/chitosan films with copper-doped phosphate glasses for orthopaedic implants

Altering the percolation threshold of PA66‐copper hybrid in an electroless copper deposition process by surface activation of the polymer

Mixed-Material Feedstocks for Cold Spray Additive Manufacturing of Metal–Polymer Composites

Sol–Gel Derived Alumina Particles for the Reinforcement of Copper Films on Brass Substrates

Eco-friendly, cost-effective electroless Ag plating based on a novel Ni–P activation process on magnesium titanate ceramic

A New Activation Method For Electroless Metal Plating: Palladium Laden Via Bonding With Self-Assembly Monolayers

In-situ synthesis of graphene-like carbon encapsulated copper particles for reinforcing copper matrix composites

Selective Cu electroplating enabled by surface patterning and enhanced conductivity of carbon fiber reinforced polymers upon air plasma etching

A facile process to fabricate metal coating on PET sheet: Preparation of highly active polymer brush/Ag particle and its application in electroless copper plating