Abstract:Silicon carbide (SiC) MOSFETs are expected to replace Si bipolar transistors partially in applications such as automotive, railroad, and other high-voltage applications. But the resistance of the MOS inversion layer channel limits the performance of MOSFETs. It has been clarified that the effective carrier density in the inversion channel is significantly reduced by the carrier trapping by the high density of defect states distributed nearby SiO2/SiC interface. In this study, our understanding of oxidation and nitridation reactions of SiC for designing the gate stack formation processes to improve the MOS interface characteristics is presented. Choosing SiO 2 as a gate dielectric for SiC is favorable from various aspects including its ability to form a thermodynamically stable interface with SiC, which is free of reactions at the process temperature. However, from a microscopic point of view, Si-O bond alone cannot cover the whole surface of SiC and the excess C atoms on the surface causes the formation of defect states. One of the possible approaches has been employing an appropriate thermal oxidation condition to enhance the excess carbon elimination by forming CO. For example, we have experimentally demonstrated a significant reduction of D it by employing high-temperature thermal oxidation with a rapid heating furnace [1]. However, such approach seems to bring a serious drawback such as defect formation in the surface region of SiC, experimentally detected by a lattice distortion in the beneath of SiO 2 after high-temperature oxidation [2]. One of the possible reasons for such deterioration would be an invasion of activated oxygen atoms into the surface region of SiC [3]. A possible approach to avoid such drawback of high-temperature oxidation process would be utilizing H 2 O vapor for the formation of SiO 2 /SiC interface at relatively lower temperature while avoiding the damages on SiC surface [4], since H 2 O oxidation was found to be advantageous to remove CO more efficiently than O 2 oxidation even at low temperature. On the other hand, another approach to passivate SiC surface is the surface nitridation technique, which is the most common way in industry to fabricate SiC MOS interface typically achieved by high-temperature annealing in NO gas [5]. Nitridation can replace the topmost C sites with N without inducing significant distortion in the SiC surface structure, to suppress the C-related defect formation at the interface. The advantage of this reaction is that it proceeds self-limited manner and N atoms are introduced only on the topmost surface of SiC. Note that NO gas triggers the surface nitridation by removing the surface C atoms in the form of CO by oxidation. Actually, a very similar reaction occurs even when SiC is annealed in N 2 [6] ambient with a slight addition of O 2 . We experimentally found that the surface N density saturated with different values when we employed various N 2 +O 2 atmosphere with different O 2 concentration. Therefore we setup a simple model to describe the saturation behavior, which is determined by the balance between the rate of N uptake (N + ) and the rate of N desorption (N ‒ ) mainly due to the oxidation reaction [7]. This model was found to represent the time-dependent change of surface N density well, by assuming that N + remained constant during the reaction and N ‒ was proportional to both the reaction rate of interface oxidation and the surface N density [8]. Based on this simplified model, it is possible to design a process to tune the N density. By choosing appropriate temperature and oxygen partial pressure we can increase N density at the surface to minimize the interface trap density. Further improvement of surface N density would be achieved by further controlling of the blance between N uptake and N desorption reactions. As we have discussed so far, the role of materials science to clarify the interface phenomena is significantly important to achieve a further improved SiC MOS interface characteristics for the next generation SiC power MOSFET process technology. [1] R. Kikuchi and K. Kita, Appl. Phys. Lett. 105, 032106 (2014). [2] A. D. Hatmanto and K. Kita, Appl. Phys. Express 11, 011201 (2018). [3] A. D. Hatmanto and K. Kita, Jpn. J. Appl. Phys. 59, SMMA02 (2020). [4] H. Hirai and K. Kita, Appl. Phys. Lett. Appl. Phys. Lett. 113, 172103 (2018). [5] J. Rozen et al., J. Appl. Phys. 105, 124506 (2009). [6] A.Chanthaphan et al., AIP Adv. 5, 097134 (2015). [7] T. Yang and K. Kita, Jpn. J. Appl. Phys. 61, SC1077 (2022). [8] T. Yang and K. Kita, SSDM 2023, Chiba.

Improved device characteristics obtained in 4H-SiC MOSFET using high-k dielectric stack with ultrathin SiO2-AlN as interfacial layers

Pre-deposition Growth of Interfacial SiO2 Layer by Low-Oxygen-partial-pressure Oxidation in the Al2O3/4H-SiC MOS Structure

Multi-Layer High-K Gate Stack Materials for Low Dit 4H-SiC Based MOSFETs

Analysis of 4H-SiC MOSFET with distinct high-k/4H-SiC interfaces under high temperature and carrier-trapping conditions

Exploring High-Temperature Reliability of 4H-SiC MOSFETs: A Comparative Study of High-K Gate Dielectric Materials

Design of Al2O3/LaAlO3/SiO2 Gate Stack on Various Channel Planes for High-Performance 4H-SiC Trench Power MOSFETs

Leakage Current Behavior in HfO2/SiO2/Al2O3 Stacked Dielectric on 4H-SiC Substrate

(Invited) MOS Interface Control Technologies for Advanced III-V/ Ge Devices

Interface Properties Study on SiC MOS with High-K Hafnium Silicate Gate Dielectric

MOS interface control of high mobility channel materials for realizing ultrathin EOT gate stacks

Saturation Thickness of Stacked SiO2 in Atomic-Layer-deposited Al2O3 Gate on 4H-Sic

High-k gate stack Hf x Ti1−x ON/SiO2 for SiC MOS devices

Tuning the high-κ oxide (HfO2, ZrO2)/4H-SiC interface properties with a SiO2 interlayer for power device applications

Increasing Mobility in 4H-SiC MOSFETs with Deposited Oxide by In-Situ Nitridation of SiC Surface

(Invited) Design of Surface Oxidation and Nitridation Reactions on 4H-SiC for the Advanced SiC Gate Stack Formation Processes

An Investigation into the $HfO_2/Si$ Interface: Materials Science Challenges and their Effects on MOSFET Device Performance

Improved high-field reliability for a SiC metal–oxide–semiconductor device by the incorporation of nitrogen into its HfTiO gate dielectric

Interface study of atomic-layer-deposited HfO2/NO-nitrided SiO2 gate dielectric stack on 4H SiC

Electrical Characterization of HfO2/4H-SiC and HfO2/Si MOS Structures

Numerical Analysis of 4H-SiC MOSFET Design Including High-k Gate Dielectrics for Power electronic Applications

Toward the Understanding of Stacked Al-Based High-k Dielectrics for Passivation of 4H-SiC Devices