Abstract:In the copper (Cu) hydrometallurgical process, the extractant, and impurity ions in the leaching process would inevitably enter the electrolyte in the electrodeposition with the process cycle. And with the recycling of electrolyte, the impurities would continue to accumulate. When the accumulation of impurities exceeds a certain limit, it could have a large negative impact on the deposited Cu. In this paper, the effects of the ferrous ion (Fe 2+ ) and the commonly used extractant Lix984 (5-nonylsalicylaldehyde oxime and 2-hydroxy-5-nonylacetophenone oxime 1:1 mixture) on the morphology, current efficiency (CE) and energy consumption of Cu cathodes were investigated. In addition, the electrochemical mechanisms were investigated using electrochemical methods such as cyclic voltammetry (CV), linear scanning voltammetry (LSV), Tafel linear fitting and chronopotentiometry (CP). When the Fe 2+ concentration was 2.0 g/L, the CE decreased sharply to 93.63%, which was 6.21% lower than normal. And the Lix984 at 50 mg/L reduced the CE from 5.88% to 93.99%. The energy consumption increased by up to 89 kWh/ (t Cu). Electrochemical studies showed that high concentrations of Fe 2+ and/or Lix984 in the electrolyte significantly inhibited Cu deposition by increasing the overpotential, decreasing the deposition rate, and covering the electrode surface, resulting in larger Cu coating roughness and larger grain size. Therefore, the concentration of Fe 2+ and organic impurities in the electrolyte should be appropriately controlled before proceeding to Cu electrodeposition to obtain a favorable quality Cu cathode.

Effect of Fe3+ on electrowinning of copper by CE

Effect of Cerium on Microstructure, Texture and Properties of Ultrahigh-Purity Copper

Influence of Fe Ions on Anode Performance and the Mechanism of Action during Copper Electrowinning Process

Effect of Zn2+ on the extraction of copper by cyclone electrowinning from simulated copper-containing electrolyte

Volatilization of Zn and Pb and Preparation of Integrated Micro-Electrolysis Filter from Copper Slag and Its Application for Removing Cr(VI) from Aqueous Solution.

Roles and influencing mechanisms of Fe2+ and Lix984 in copper electrodeposition

Effects of Fe(III) and Cu(I) on Electrodeposition and Microstructure Characterization for Acid Plating Bath

Enhanced removal of copper ions from wastewater using small spherical Fe-N-C material via selective electro-sorption: Experiment and calculation

Effects of Acid Pretreatment on Purity of Copper Foil Recovered by Electrolytic Refining from Waste Printed Circuit Board

Effects of Catholyte Conditioning on Electrokinetic Extraction of Copper from Mine Tailings

Copper recovery from treatment of simulated copper-iron wastewater using fluidized-bed homogeneous crystallization technology

RECOVERY OF Cu, Zn AND CYANIDE FROM STRONG COPPER CYANIDE SOLUTIONS BY ELFETROWINNING-PARTIAL ACIDIZING

Recovery of copper and water from copper-electroplating wastewater by the combination process of electrolysis and electrodialysis

Enhancing Destruction of Copper (I) Cyanide and Subsequent Recovery of Cu(I) by a Novel Electrochemical System Combining Activated Carbon Fiber and Stainless Steel Cathodes

The Influence of Rare Earth Ce on the Microstructure and Properties of Cast Pure Copper

Effective recycling of Cu from electroplating wastewater effluent via the combined Fenton oxidation and hydrometallurgy route

Breaking the Fe3O4-wrapped copper microstructure to enhance copper–slag separation

Chalcopyrite Leaching in Ferric Sulphate: The Effect of Fe3O4-CuFeS2 Galvanic Couple on the Cu Dissolution

Electrowinning Cu and Zn from a Strong Copper Cyanide Solution

Enhanced recovery of high-purity Fe powder from iron-rich electrolytic manganese residue by slurry electrolysis

Copper Recovery from Industrial Bimetallic Composite Ionic Liquids by Direct Electrodeposition and the Effect of Temperature and Ultrasound