Abstract:With the advantages of a high theoretical capacity, proper working voltage, and abundant reserves, silicon (Si) is regarded as a promising anode for lithium-ion batteries. However, huge volume expansion and low electronic conductivity impede the commercialization of Si anodes. We devised a one-step, vacuum-assisted reactive carbon coating technique to controllably produce micrometer-sized nanoporous silicon confined by homogeneous N-doped carbon nanosheet frameworks (), achieved by the solid state reaction of a commercial bulk precursor and the subsequent evaporation of byproducts. The graphitization degree, C and N contents of the carbon shell, as well as the porosity of Si can be regulated by adjusting the synthetic conditions. A rational structure can mitigate volume expansion to maintain structural integrity, enhance electronic conductivity to facilitate charge transport, and serve as a protected layer to stabilize the solid electrolyte interphase. The anode enables a stable cycling performance with 95.68% capacity retention for 4000 cycles at 5 A g–1. Furthermore, a flexible 2D/3D architecture is designed by conjugating with MXene. Lithiophilic homogenize Li nucleation and growth, evidenced by structural evolutions of @NCNF deposited Li. The application potential of and @NCNFs is estimated via assembling full cells with LiNi0.8Co0.1Mn0.1O2 and LiNi0.5Mn1.5O4 cathodes. This work offers a method for the rational design of alloy-based materials for advanced energy storage.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsnano.1c11098.Experimental section; XRD pattern and XPS spectra of Mg2Si and C3N4; ID/IG values, C and N contents, N2 adsorption/desorption isotherms, pore size distributions, TEM, HRTEM, and SAED of ; XRD, XPS, SEM and EDS mapping images of Nano-Si; charge/discharge curves of Nano-Si and anodes for LIBs at different rates; digital photograph (electrode and separator), SEM, thickness and thickness changes of Nano-Si and anodes before and after cycles; GITT and diffusion coefficients of and ; XRD, SEM, and EDS mapping images of NCM and LNMO; charge/discharge curves and capacity retentions of a full cell with Nano-Si and anodes at different rates (NCM and LNMO cathodes); EIS curves of a cycled full cell with Nano-Si and anodes (NCM and LNMO cathodes); XRD, SEM, and EDS mapping images of MAX; digital photograph of MXene solution; XRD, Raman, XPS, SEM, EDS mapping images, and digital photograph of MXene; SEM of @NCNFs; SEM of structural evolutions of Cu foil and @NCNFs deposited Li with different area capacities; voltage profiles on Cu and @NCNFs; EIS and SEM of Cu, @NCNFs, , and @ for Li metal anode after cycles; charge/discharge curves and capacity retentions of a full cell with and @ anodes at different rates (NCM and LNMO cathodes); EIS curves of a cycled full cell with and @ anodes (NCM and LNMO cathodes) (PDF)This article has not yet been cited by other publications.

Prelithiated Carbon Nanotube‐Embedded Silicon‐based Negative Electrodes for High‐Energy Density Lithium‐Ion Batteries

In‐Vitro Electrochemical Prelithiation: A Key Performance‐Boosting Strategy for Carbon Nanotube‐Containing Silicon‐Based Negative Electrodes in Li‐Ion Batteries

In Situ Nitrogen-Doped Helical Mesoporous Carbonaceous Nanotubes for Superior-High Lithium Anodic Performance

Non-destructive Chemical Prelithiation of VO2(B) Anodes Constructing a Multifunctional Interphase Layer for Advanced Li-Ion Batteries

A High-Efficient Stable Surface-Prelithiated Li1.2ni0.13co0.13mn0.54o2 Cathode Enabled by Sacrificial Lithium Nitrides for High-Energy-Density Lithium-Ion Batteries

Impact of Electrolyte on Direct-Contact Prelithiation of Silicon-Graphite Anodes in Lithium-Ion Cells with High-Nickel Cathodes

Prelithiation of silicon-carbon nanotube anodes for lithium ion batteries by stabilized lithium metal powder (SLMP)

Tailored Pre-Lithiation of Carbon Anodes Using Melt Deposited Thin Lithium

One-Step, Vacuum-Assisted Construction of Micrometer-Sized Nanoporous Silicon Confined by Uniform Two-Dimensional N-Doped Carbon toward Advanced Li Ion and MXene-Based Li Metal Batteries

Silicon/Carbon Nanoparticles Assembled with Multifunction Carbon Nanotubes/Sheets as High-Performance Anode of Lithium-Ion Batteries

Elucidating the Chemical Pre‐Lithiation Mechanism of Hard Carbon Anodes for Ultra‐high Stability Lithium‐Ion Batteries

Nanostructured Silicon-Carbon 3D Electrode Architectures for High-Performance Lithium-Ion Batteries

“Nano-Skeleton” Si-SiOx@C Anodes towards Highly Stable Lithium-ion Batteries

Facilitating prelithiation of silicon carbon anode by localized high‐concentration electrolyte for high‐rate and long‐cycle lithium storage

Porosity‐ and Graphitization‐Controlled Fabrication of Nanoporous Silicon@Carbon for Lithium Storage and Its Conjugation with MXene for Lithium‐Metal Anode

Opportunities and Challenges of Li2C4O4 as Pre‐Lithiation Additive for the Positive Electrode in NMC622||Silicon/Graphite Lithium Ion Cells

Preparation and electrochemical performance of nanocarbon-isolated nano-sheet silicon lithium-ion battery anode material

Electrochemically pre-lithiated SiO2@C nanocomposite anodes for improved performance in lithium-ion batteries

Prelithiating Si-Based Anodes using Li-Excess Layered Positive Electrode Materials

Artificial Solid Electrolyte Interphase-Protected LixSi Nanoparticles: an Efficient and Stable Prelithiation Reagent for Lithium-Ion Batteries.

Prelithiation Activates Li(Ni0.5Mn0.3Co0.2)O-2 for High Capacity and Excellent Cycling Stability