Abstract:Fused filament fabrication is a 3D printing technique that has gained widespread use from homes to schools to workplaces. Thermoplastic filaments, such as acrylonitrile-butadiene-styrene (ABS) and polylactic acid (PLA), are extruded at temperatures near their respective glass transition temperature or melting point, respectively. Little has been reported on the inorganic elemental composition and concentrations present in these materials or the methods available for extracting that information. Because inorganic constituents may be included in the aerosolized particulates emitted during the printing process, identifying elements that could be present and at what specific concentrations is critical. The objective of the current research is to determine the range of metals present in thermoplastic filaments along with their relative abundance and chemical speciation as a function of polymer type, manufacturer, and color. A variety of filaments from select manufacturers were digested using a range of techniques to determine the optimal conditions for metal extraction from ABS and PLA polymers. The extraction potential for each method was quantified using by ICP-MS analysis. When possible, further characterization of the chemical composition of the filaments was investigated using X-ray Absorption spectroscopy to determine chemical speciation of the metal. Optimal digestion conditions were established using a high temperature, high pressure microwave-assisted acid digestion method to produce the most complete and repeatable extraction results. The composition and abundance of metals in the filaments varied greatly as a function of polymer, manufacturer, and color. Potential elements of concern present in the filaments at elevated concentration included that could pose a respiratory risk included Si, Al, Ti, Cu, Zn, and Sn. XAS analysis revealed a mixture of metal oxides, mineral, and organometallic compounds were present in the filaments that were being used to increase opaqueness impart color (dyes), polymeric catalysts, and flame retardants. This work shows that a variety of metals are present in the starting materials used for 3D printing and depending on their partitioning into 3D printed products and byproducts as well as the exposure route, may pose a health risk which merits further investigation.

Single-Particle ICP-TOFMS Analysis of Aerosol Particulate Matter Released by Fused Deposition Modeling 3D Printers

Particle measurements of metal additive manufacturing to assess working occupational exposures: a comparative analysis of selective laser melting, laser metal deposition and hybrid laser metal deposition

Measurement of sub-4 nm particle emission from FFF-3D printing with the TSI Nano Enhancer and the Airmodus Particle Size Magnifier

Evaluation of emissions and exposures at workplaces using desktop 3-dimensional printer

A pilot study of occupational exposure to ultrafine particles during 3D printing in research laboratories

Simultaneous Particle Tracking and Temperature Measurements during Additive Manufacturing using a High-speed Spectral Plenoptic Camera

Capturing PM2.5 Emissions from 3D Printing Via Nanofiber-based Air Filter.

Variability in the inorganic composition of colored acrylonitrile-butadiene-styrene and polylactic acid filaments used in 3D printing

Additive Manufacturing: Assessing Metal Powder Quality Through Characterizing Feedstock and Contaminants

In Situ Characterization of Laser Powder Bed Fusion Using High-Speed Synchrotron X-ray Imaging Technique

Online Monitoring of an Additive Manufacturing Environment Using a Time-of-flight Mass Spectrometer

Broadband infrared confocal imaging for applications in additive manufacturing

Factors affecting particle characterization of powders used in additive manufacturing

Transient Dynamics of Powder Spattering in Laser Powder Bed Fusion Additive Manufacturing Process Revealed by In-Situ High-Speed High-Energy X-Ray Imaging

Analysis of complex particle mixtures by asymmetrical flow field-flow fractionation coupled to inductively coupled plasma time-of-flight mass spectrometry

Unlocking the nanoparticle emission potential: a study of varied filaments in 3D printing

Schlieren and X-Ray Imaging of Laser-Particle Interactions in Metal Additive Manufacturing

In-situ High-Speed X-ray Imaging of Piezo-Driven Directed Energy Deposition Additive Manufacturing

Mass spectrometric investigations into 3D printed parts to assess radiopurity as ultralow background materials for rare event physics detectors

On the potential of ultrasonic time of flight instrumentation for the monitoring of thermal phenomena in laser powder bed fusion

Defect and satellite characteristics of additive manufacturing metal powders