Abstract:Detailed investigations were conducted at a facility that manufactures and processes carbon nanofibers (CNFs). Presented research summarizes the direct-reading monitoring aspects of the study. A mobile aerosol sampling platform, equipped with an aerosol instrument array, was used to characterize emissions at different locations within the facility. Particle number, respirable mass, active surface area, and photoelectric response were monitored with a condensation particle counter (CPC), a photometer, a diffusion charger, and a photoelectric aerosol sensor, respectively. CO and CO(2) were additionally monitored. Combined simultaneous monitoring of these metrics can be utilized to determine source and relative contribution of airborne particles (CNFs and others) within a workplace. Elevated particle number concentrations, up to 1.15 x 10(6) cm(-3), were found within the facility but were not due to CNFs. Ultrafine particle emissions, released during thermal treatment of CNFs, were primarily responsible. In contrast, transient increases in respirable particle mass concentration, with a maximum of 1.1 mg m(-3), were due to CNF release through uncontrolled transfer and bagging. Of the applied metrics, our findings suggest that particle mass was probably the most useful and practical metric for monitoring CNF emissions in this facility. Through chemical means, CNFs may be selectively distinguished from other workplace contaminants (Birch et al., in preparation), and for direct-reading monitoring applications, the photometer was found to provide a reasonable estimate of respirable CNF mass concentration. Particle size distribution measurements were conducted with an electrical low-pressure impactor and a fast particle size spectrometer. Results suggest that the dominant CNF mode by particle number lies between 200 and 250 nm for both aerodynamic and mobility equivalent diameters. Significant emissions of CO were also evident in this facility. Exposure control recommendations were described for processes as required.

Measurement of sub-4 nm particle emission from FFF-3D printing with the TSI Nano Enhancer and the Airmodus Particle Size Magnifier

Fmps Measurement Of Nanoparticle Pollutant In Office Air

Unlocking the nanoparticle emission potential: a study of varied filaments in 3D printing

Factors That Govern Sub-3 Nm Particle Measurements in an Airmodus® PSM and a TSI® DEG–SMPS

Size-Resolved Single-Particle Fluorescence Spectrometer for Real-Time Analysis of Bioaerosols: Laboratory Evaluation and Atmospheric Measurements

Sub-3nm Particle Detection with Commercial TSI 3772 and Airmodus A20 Fine Condensation Particle Counters

Sub-3 nm Particle Detection with Commercial TSI 3772 and Airmodus A20 Fine Condensation Particle Counters

Sub-Micro Particle Matter Detection for Metal 3-D Printing Workshop

A pilot study of occupational exposure to ultrafine particles during 3D printing in research laboratories

Investigation of Ultraﬁne Particle Emissions of Desktop 3D Printers in the Clean Room

Aerosol monitoring during carbon nanofiber production: mobile direct-reading sampling

Evaluation of emissions and exposures at workplaces using desktop 3-dimensional printer

Characteristics of Scanning Flow Condensation Particle Counter (SFCPC): A Rapid Approach for Retrieving Hygroscopicity and Chemical Composition of Sub-10 Nm Aerosol Particles

Comparison of Ultrafine Particle Release from Hardcopy Devices in Emission Test Chambers and Office Rooms

Reducing ultrafine particulate emission from multiple 3D printers in an office environment using a prototype engineering control

Single-Particle ICP-TOFMS Analysis of Aerosol Particulate Matter Released by Fused Deposition Modeling 3D Printers

Particle measurements of metal additive manufacturing to assess working occupational exposures: a comparative analysis of selective laser melting, laser metal deposition and hybrid laser metal deposition

Overview of measurements and current instrumentation for 1–10 nm aerosol particle number size distributions

Optically Sizing Single Atmospheric Particulates with a 10-Nm Resolution Using a Strong Evanescent Field.

Metrological Performances of A Diffusion Charger Particle Counter for Personal Monitoring

First Measurements of the Number Size Distribution of 1–2 Nm Aerosol Particles Released from Manufacturing Processes in a Cleanroom Environment