Abstract:In this work, a low-noise and high-rate front-end readout application-specific integrated circuit (ASIC) named SECALROC2 for the electromagnetic calorimeter (ECAL) in the super tau-charm factory (STCF) is presented. The chip is designed to process signals generated from avalanche photodiode detectors (APDs) for both energy and time measurement. The large detector capacitance and leakage current of the APD pose a great challenge to the noise and speed performance of the front-end readout circuit (ROC). A low-noise preamplifier and a fifth-order high-linearity shaper with adjustable peaking times are proposed to decrease noise induced by the 270-pF detector capacitance. A peak detect-and-hold circuit and a high-linearity differential analog buffer are adopted to convert each peak voltage of the shaper to differential voltages with sufficient driving capability. A fast shaper and a discriminator are implemented to produce trigger signals for the time of arrival (TOA) measurement. To reduce the complexity and power consumption of the ECAL system, a 12-bit 10-MS/s pipelined analog-to-digital converter (ADC) and a 16-bit three-stage time-to-digital converter (TDC) with 42-ps bin size TDC are integrated on-chip for full-digitalized outputs. This ASIC was designed and fabricated in a standard commercial 1P6M 0.18-mu m mixed-signal CMOS process and the chip area occupancy is 2.4 x 1.6 mm(2). The experimental results show that the input charge of the ASIC ranges from 3.2 to 400 fC. The measured nonlinear error of the system is less than 2.5% with an event rate up to 400 kcps. The equivalent noise charge (ENC) is 1367 e(-) + 4.93 e(-)/pF at 800-ns peaking time. The timing resolution is better than 540 ps at an input charge of 160 fC. The measured ENC can achieve 3820 e(-) when the ASIC is connected to an APD detector. The effective number of bits (ENOB) of the ADC is 10.8-bit when operated at 10 MS/s.

A Mixed-Signal Micromegas Readout ASIC Prototype With Automatic Charge Measurement Range Calibration

Design and Testing of a 0.8 V Low-voltage High-rate Prototype Readout ASIC for the Micro-Pattern Gas Detector

Design and Development of a Front-End Readout ASIC for APD-Based STCF Electromagnetic Calorimeter

SECALROC2: A Low-Noise, High-Speed, and Full Digital Outputs Front-End ASIC for STCF Electromagnetic Calorimeter With APD Detectors

Design of a Low-Power Front-End Readout ASIC Based on Energy-Efficient Amplifiers, Featured 126 e-(rms), 0.6 mW/Channel for Si-PIN Detectors

A Low Noise Apd Readout Asic For Electromagnetic Calorimeter In Hiepa

Design and Performance of a 16-Channel Radiation-Hardened Low-Noise Front-End Readout ASIC for CZT-based Hard X-ray Imager

A multichannel front end ASIC for PMT readout in LHAASO WCDA

SENSROC12V4: a Low Noise Programmable Readout ASIC for Si-PIN Detectors

Design and preliminary performance of a novel mixed-signal front-end electronics with post digital shaping for CZT detectors

Design and Characterization of a Low-Noise Front-End Readout ASIC in 0.18- $\mu$ M CMOS Technology for CZT/Si-PIN Detectors

Design and Testing of a Prototype ASIC for the MTPC Readout at CSNS Back-n White Neutron Source

A High-Speed Low-Noise Front-End ASIC Prototype for Ionization Chambers of High-Intensity Beam Monitoring

An Analogue Front-End ASIC Prototype Designed For PMT Signal Readout

Design and Characteristics of a Multichannel Front-End ASIC Using Current-Mode CSA for Small-Animal PET Imaging.

SENSROC12: A Four-Channel Binary-Output Front-End Readout ASIC for Si-PIN-Based Personal Dosimeters

Design of a Pixel Readout ASIC Using Super Pixel Circuits with a Built-in LDO Regulator for Hybrid X-ray Imaging Detectors

Casagem: A Readout Asic for Mpgds

Design of a Low-Noise Photon-Count Readout ASIC for Si-PIN-Based Personal Dosimeters with Low Energy Detection Threshold

Evaluation of a Front-End ASIC Prototype for the Readout of PMTs in Water Cherenkov Detector Array

Characteristics of a Multichannel Low-Noise Front-End ASIC for CZT-based Small Animal PET Imaging