Abstract:Abstract To establish the effect of tube size as a factor in heat transfer and pressure drop for gases flowing transversely over tube banks of a given tube arrangement, new experimental determinations have been made for several tube sizes, and results compared with those of Pierson who used very small tubes of 0.31 in. diameter. The arrangements used included some of those studied by Pierson and these tests on a larger scale have served as a check on the accuracy of his small-scale results with a different method and different imposed conditions, and the applicability of model results to full-scale equipment, the two series forming parts of a research program of the Babcock & Wilcox Company. Nine tube arrangements as shown in Fig. 1, defined by center spacings in the direction of flow and transversely, were used with tubes of both 1⁄2 in. diameter and 11/12 in. diameter, the spacing ranging from a minimum of 11⁄4 × 11⁄4 diameters, to a maximum of 2 × 3 diameters with ten rows in the direction of flow both in-line and staggered, and ten tubes wide except for one case of eight tubes wide. In addition, three arrangements of tubes of 2-in. diameter were used in banks of ten rows deep and from nine to fifteen tubes wide. For the banks of smaller tubes, 1⁄2 in. and 11/12 in. diameter, heat was transferred from hot gases outside to cold water inside, while for the banks of 2 in. tubes, heat was transferred from condensing steam inside to air outside. Values of gas-boundary conductance and pressure drop were found for several identical tube arrangements and spacing and three tube sizes of 1⁄2 in., 11/12 in., and 2 in., with heat flow inward and outward; these are found to be consistent with those for the Pierson model tubes of 0.31 in. diameter. Heat-transfer rates are reported in terms of the Nusselt number, and pressure drop in terms of the Fanning equation for friction factor, both of them in relation to the Reynolds number. For values of the Reynolds number in the range of commercial practice, the Nusselt number varies as the 0.61 power of the Reynolds number, and the friction factor is not so regularly related to the Reynolds number but varies with the tube arrangement. Values of both gas-boundary conductance and friction factor for a given tube arrangement are consistent for all tube sizes from the full-scale 2-in. tubes down to the Pierson model tubes of 0.31 in., including the intermediate sizes of 1⁄2-in. and 11/12-in. tubes, thus confirming the validity of the principle of similarity applied to tube banks in spite of some departure from true geometric similarity in the ratio of length to diameter or to intertube space for the range of Reynolds’ numbers tested, 2000 to 70,000.

Efficiency Parameters for Heat Transfer in Tube Banks

Heat Exchange in Staggered Threaded Pipe Banks with Similar Developed Surface Patterns under Natural Draft Conditions

Heat Transfer and Flow Resistance in Crossflow over Corrugated Tube Banks

Numerical Simulation of Heat Transfer in Finned Tube of Heat Recovery Unit Using Fluid-Solid Coupled Method

Parametric Study and Field Synergy Principle Analysis of H-type Finned Tube Bank with 10 Rows

Mathematical Investigation of Heat Transfer Characteristics and Parameter Optimization of Integral Rolled Spiral Finned Tube Bundle Heat Exchangers

Efficiency of Heat Transfer Surfaces Using the Method of Effective Parameters

Numerical Study On Low Reynolds Number Heat Transfer In Alternating Elliptical Axis Tube

Numerical and experimental study of the heat transfer process in a double pipe heat exchanger with inner corrugated tubes

Innovative analysis of local and average air-side heat transfer coefficients in fin-and-tube heat exchangers using CFD and experimental method

Numerical Study of Different Pr Number Medium Turbulent Cross Flow in Staggered Tube Bundle

Experimental Investigation of Effects of Equipment Size on Convection Heat Transfer and Flow Resistance in Cross Flow of Gases Over Tube Banks

Experimental and numerical characterization of single-phase pressure drop and heat transfer enhancement in helical corrugated tubes

Experimental Investigation of Heat Transfer and Pressure Drop Characteristics of H-type Finned Tube Banks

Airside Heat Transfer and Pressure Loss Characteristics of Bare and Finned Tube Heat Exchangers Used for Aero Engine Cooling Considering Variable Air Properties

Enhancing heat exchanger performance through hybrid angle of attack control for drop-shaped tubes

Parametric Study and Multiple Correlations on Air-Side Heat Transfer and Friction Characteristics of Fin-and-tube Heat Exchangers with Large Number of Large-Diameter Tube Rows

Numerical Investigation Of Effect Of Tube Shape On Air-Side Heat Transfer And Pressure Drop Characteristics Of A Finned Tube Heat Exchanger

Heat Transfer and Pressure Loss In Combined Tube Banks With Triple-Finned Tubes

Heat transfer coefficient in elliptical tube at the constant heat flux

Comparison of Individual Air-Side Row-By-Row Heat Transfer Coefficient Correlations on Four-Row Finned-Tube Heat Exchangers