Abstract:It is well known that the photothermal conversion performance of solar-driven interfacial water evaporation systems is known to have a stronger photothermal conversion performance than suspended water evaporation systems due to their relatively strong ability to suppress overall heat loss. Natural polymer chitosan and gelatin can form a three-dimensional interpenetrating network (IPN) sponge to provide an interface for water evaporation due to strong hydrogen bonding and electrostatic attraction interaction. However, the lack of effective light absorption, the intrinsic short lifetime, and the poor photothermal conversion greatly compromise their steam generation performance. Here, we fabricated a chitosan/gelatin-based IPN sponge incorporated with melanin-coated titania hollow nanospheres () as a solar thermal converter, which is designed to exhibit a unique cavity structure and vertical channels. The cavity structure of melanin-coated titania acts as a solar thermal transducer, while the chitosan/gelatin-based IPN sponge acts as a single-pass water pump. A water hyacinth-inspired evaporation system shows outstanding steam generation performance, and the highest steam generation rate was 3.17 kg m–2 h–1 under a 2.5 sun illumination because of the cavity enhancement effect, far above TiO2 particles and reported photo-thermal conversion materials. More importantly, the embedding of MPT-h nanoparticles in the IPN sponge effectively inhibits the growth of bacteria in the vertical channels, resulting in an antibacterial solar-driven water evaporator. This advanced sponge provides a cost-effective and practical sustainable energy technique for solar-driven wastewater treatment.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.0c21690?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.0c21690</a>.Schematic diagram of the sponge fabrication process (Figure S1); stability, porosity and capillarity of the sponge (Notes S1); weight loss ratio of the sponge (Figure S2); swelling ratio, saturated water content, and calculated water transport rate of the sponge (Figure S3); determination of pHpzc (Figure S4); schematic illustration of the formation mechanism of the sponge (Figure S5); SEM image, light absorption, and reflectance spectra of the sponge (Figure S6); surface temperature of different samples (Figure S7); infrared radiation thermal images of different samples (Figure S8); mass change of evaporated water and the actual evaporative efficiency of the sponge (Figure S9); mass change of evaporated water and the actual evaporative efficiency in the sponge with different MPT-h contents (Figure S10); duration test of the sponge (Figure S11); calculation of steam generation efficiency (Table S1); the relevant results of the current solar-driven steam generation system experiments (Table S2); roof-solar still (Figure S12); infrared images of the (Figure S13); antibacterial property of sponges (Figure S14); representative TiO2 materials with their antibacterial performances (Table S3); and water evaporation rate of the sponge with different thicknesses (Notes S2) (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c21690/suppl_file/am0c21690_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Photothermal Water Evaporation via Hollow-CuS Embedded PDMS Sponge Under UV, Visible, and IR Irradiation

Construction of a Three-Dimensional Interpenetrating Network Sponge for High-Efficiency and Cavity-Enhanced Solar-Driven Wastewater Treatment

A 3D Opened Hollow Photothermal Evaporator for Highly Efficient Solar Steam Generation

Copper-Nanoparticle-Decorated Hydrothermal Carbonaceous Carbon-Polydimethylsiloxane Nanocomposites: Unveiling Potential in Simultaneous Light-Driven Interfacial Water Evaporation and Power Generation

A Gelation‐Stabilized Strategy toward Photothermal Architecture Design for Highly Efficient Solar Water Evaporation

CuS Hollow Nanospheres/Cellulose Composite Film as a Recyclable Interfacial Photothermal Evaporator for Solar Steam Generation

Janus Polysulfone Gradient Hollow Fiber Membranes with Interfacial Photothermal Evaporation by Optimization of Water Transport and Thermal Management

Conformal Microfluidic‐Blow‐Spun 3D Photothermal Catalytic Spherical Evaporator for Omnidirectional Enhanced Solar Steam Generation and CO2 Reduction

Conformal Microfluidic‐Blow‐Spun 3D Photothermal Catalytic Spherical Evaporator for Omnidirectional Enhanced Solar Steam Generation and CO 2 Reduction

Solar-driven water evaporation using a collaborative photothermal conversion material system based on carbonized waste polyphenylene sulfide and copper sulfide

Twisting Two-Dimensional Photothermal Sponges for Boosting Solar Steam Generation

Black TiO 2 -infused polydimethylsiloxane composites for efficient solar-assisted water evaporation and thermoelectric energy generation

Multifunctional photothermal materials based on natural pumices for high efficiency solar‐driven interface evaporator

Dome-arrayed chitosan/PVA hydrogel-based solar evaporator for steam generation

Surface Patterning of Two-Dimensional Nanostructure-Embedded Photothermal Hydrogels for High-Yield Solar Steam Generation

The core-shell CuO/PDA@TA-Fe nanowires arrays on 3D Cu foam for solar evaporator and water purification with highly efficiency and stability

Copper sulfide integrated functional cellulose hydrogel for efficient solar water purification

Sponge-Based Aerogels for Efficient Solar Steam Generation

A High-Efficiency and Low-Cost Interfacial Evaporation System Based on Graphene-Loaded Pyramid Polyurethane Sponge for Wastewater and Seawater Treatments

A stable and efficient hydrogel/sponge solar evaporator with splendid water supply

Unique photothermal material: Copper phosphate (Cu 3 P 2 O 8 ) with broadband visible-to-near-infrared absorption properties for efficient solar steam generation