Abstract:The state-of-the-art solar-thermal evaporators demonstrating high energy utilization efficiency, a high evaporation rate, and salt rejection are highly desirable in solar-driven low-energy water purification/harvesting. Herein, a novel Janus solar evaporator is constructed by loading polypyrrole (PPy) nanobelts on the polyvinyl alcohol (PVA) hydrogel. The PPy nanobelts present a high solar absorption of 98.3%, leading to a localized solar-thermal efficiency of 82.5% when insulated from bulk water by the PVA hydrogel. The porous PVA hydrogel and the hydrophilic PPy nanobelts enable the efficient three-dimensional water transport. Taking advantages of the synergistic effect in the water-energy nexus, the Janus PPy hydrogel evaporator evaporates water with a high rate of 2.26 kg m–2 h–1 via 80.1% solar energy from 1 sun irradiance with a low PPy loading of ∼3 mg cm–2 even at a rate of 2.64 kg m–2 h–1 via 96.3% solar energy for a biomimetic conical evaporator. The Janus evaporator presents superior salt-resistant desalination and contaminant purification performance in seawater and sewage. Furthermore, a portable solar-thermal purifier equipped with the Janus evaporator desalts real seawater far above the drinking water standard with over a 99.9% salt rejection rate and eliminates 95.8% of chemical oxygen demand in real sewage, highlighting its potential for advanced clean water harvesting.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsami.1c13584.Instruments and characterization; desalination and purification tests; instruments; calculations of total solar absorption of PPy nanobelts; calculations of vaporization enthalpy and energy efficiency; digital images of the bulk FeOCl crystal and superfine FeOCl powder; digital images of PPy dispersions in DMSO; XRD pattern of PPy nanobelts; FTIR spectra of PPy nanobelts, PVA and the PPy-PVA compound; temperature curve of the PPy nanobelts under 1 sun irradiation over time; calculations of solar-thermal conversion efficiency; mechanical strength of the PVA hydrogel; π–π interactions of PPy nanobelts; water contact angle of the PPy nanobelt film; UV–vis–NIR reflectance spectra of the upper surface of both flat and conical evaporators; evaporation rate of the conical Janus-type PPy hydrogel evaporator under 1, 2, and 5 sun irradiation; mass loss of simulated average seawater for the conical Janus evaporator with a PPy nanobelt loading content of 3 mg cm–2 compared with the bare pure water as the blank control experiment under 1 sun; corresponding fitted calibration curve of UV–vis absorbance versus gentian violet concentration at 588 nm; water transport rate of the PVA hydrogel; and calculations of COD (PDF)Washing test (MP4)This article has not yet been cited by other publications.

A High-Efficiency and Low-Cost Interfacial Evaporation System Based on Graphene-Loaded Pyramid Polyurethane Sponge for Wastewater and Seawater Treatments

Highly Efficient Solar-Driven Interface Water Evaporation Achieved on Polypyrrole@Single-Sided Flannel

Scalable, bio-inspired and self-floating bi-layer polyurethane foam solar evaporator with excellent capillary hydrodynamic effect

A stable and efficient hydrogel/sponge solar evaporator with splendid water supply

A flexible and highly efficient graphene-based photothermal evaporation device with independent water transport and photothermal absorption system

Portable solar interfacial evaporator based on polyimide nanofiber aerogel for efficient desalination

Hydrophilic Polystyrene Porous Skeleton Prepared Via High Internal Phase Emulsion Template for Efficient Solar-Driven Interfacial Evaporation

Polyethersulfone-silica aerogel/ polypyrrole solar evaporation membrane for wastewater treatment and desalination

A flexible and salt-rejecting electrospun film-based solar evaporator for economic, stable and efficient solar desalination and wastewater treatment

Cost-Effective and Scalable Solar Interface Evaporators Derived from Industry Waste for Efficient Solar Steam Generation

Enhanced Solar-to-Heat Efficiency of Photothermal Materials Containing an Additional Light-Reflection Layer for Solar-Driven Interfacial Water Evaporation

Liquefied‐chitin polyurethane foam construction of high‐efficiency solar evaporator for seawater purification

Janus Polypyrrole Nanobelt@Polyvinyl Alcohol Hydrogel Evaporator for Robust Solar-Thermal Seawater Desalination and Sewage Purification

A Facile and General Strategy to Deposit Polypyrrole on Various Substrates for Efficient Solar‐Driven Evaporation

Assembled Wood-Polyester Fabric-Hydrogel Janus Evaporator for Sustainable Seawater Desalination

Double-layered solar evaporator based on polymeric ionic liquid grafted attapulgite and MXene/PPy for efficient desalination and photodegradation

A Bilayered Wood-Poly(3,4-ethylenedioxythiophene):Polystyrene Sulfonate Hydrogel Interfacial Evaporator for Sustainable Solar-Driven Sewage Purification and Desalination

A Gelation‐Stabilized Strategy toward Photothermal Architecture Design for Highly Efficient Solar Water Evaporation

Polyimide-based superhydrophilic porous membrane with enhanced thermal insulation for efficient interfacial solar evaporation

High-flux flowing interfacial water evaporation under multiple heating sources enabled by a biohybrid hydrogel

Intensifying Solar Interfacial Heat Accumulation for Clean Water Generation Excluding Heavy Metal Ions and Oil Emulsions