Abstract:Ultrafiltration hollow-fiber membranes were prepared from polyetherimide (PEI) with a wet spinning method. The effects of N,N-dimethylacetantide (DMAc) as a solvent additive in the internal coagulant and acetic acid as a non-solvent additive in the dope solution on the morphologies and performances of the membranes were investigated. The influences of PEI dope concentration on membrane morphologies and properties were also studied. Scanning electron microscopy (SEM) indicates that the addition of DMAc into the internal coagulant changes the inner fiber surface from a dense skin layer to a porous structure. However, the pure water flux of the membrane decreases with the increase of DMAc content. On the other hand, the addition of acetic acid into the casting solution promotes the spinodal demixing of the membratte-forming system and suppresses the macrovoid formation in the membrane. A nodular structure forms in the fiber skin layer. With increasing acetic acid content, the pure water flux of the membrane increases about 4-fold and the solute retention shows a slight decrease. The mechanical properties can also be improved slightly by this additive. The thermal resistance of the PEI ultrafiltration membranes prepared in this work was examined by hot water treatment at 80 degrees C. No change was observed in the permeation performance of the membranes, while the study of mechanical properties shows that the elongation-at-break of the membrane decreases slightly. PEI was sulfonated by chlorosulfonic acid (CSA) in 1,2-dichloroethane. With the increase of the molar ratio of CSA to PEI repeat unit and/or reaction time, the ion-exchange capacity (IEC) of the sulfonated polyetherimide (SPEI) increases accordingly. Water uptake test and contact angle measurements show that the hydrophillicity of the SPEI increases with the increase of the IEC. Polyetherimide/sulfonated polyetherintide (PEI/SPET) ultrafiltration hollow-fiber membranes were also prepared with a dry-wet phase inversion method and SPEI was used as a polymer additive. SEM study reveals that the addition of SPEI induces the formation of nodular structure and suppresses the formation of finger-like macrovoids. With the increase of air-gap distance, it was found that the number of micropores formed in the outer fiber surface and the pore size increased. On the other hand, the pure water flux of the membrane reaches a maximum and then decreases, while the solute retention decreases at first and then levels off at longer air-gap. Based on the filtration of bovine serum albuntin (BSA) solution, it was found that the use of SPEI in the blend membranes increased their hydrophilicity.

Preparation of PES ultrafiltration membrane for treatment of emulsified oily wastewater: Effect of solvent and non-solvent on morphology and performance

Effect of Different Solvents, Pore-Forming Agent and Solubility Parameter Differences on the Properties of PES Ultrafiltration Membrane

Preparation and Performance of Polyethersulfone Hollow-Fiber Membrane

Ultrafiltration Membrane Formation of Pes-C, Pes and Ppesk Polymers with Different Solvents

Preparation, characterization and performance of polyethersulfone ultrafiltration membranes

Polyethersulfone (PES) hollow fiber ultrafiltration membranes prepared by PES/non-solvent/NMP solution

Novel Polyethersulfone Hybrid Ultrafiltration Membrane Prepared with SiO2-g-(PDMAEMA-co-PDMAPS) and Its Antifouling Performances in Oil-in-water Emulsion Application

Polymer Concentration and Solvent Variation Correlation with the Morphology and Water Filtration Analysis of Polyether Sulfone Microfiltration Membrane

Effect of solvents in the formation of PES-based asymmetric flat sheet membranes in phase inversion method: phase separation and rheological studies

Tailoring PES membrane morphology and properties via selected preparation parameters

Preparation Of Micro-Porous Polyethersulphone Hollow Fibre Membranes Using Non-Solvent Vapour-Induced Phase Separation

Preparation of PDMS/PES hollow fiber composite pervaporation membrane

Preparation And Performance Of Ultrafiltration Membranes From Polyetherimide And Its Sulfonated Derivatives

PREPARATION OF POLY(PHTHALAZINONE ETHER SULFONE) ULTRAFILTRATION MEMBRANE

Pregelation of Sulfonated Polysulfone and Water for Tailoring the Morphology and Properties of Polyethersulfone Ultrafiltration Membranes for Dye/salt Selective Separation

Effect of Polyethersulfone Molecular Weight on Structure and Performance of Ultrafiltration Membranes

Preparation and characterization of asymmetric polyethersulfone nanofiltration membranes: The effects of polyvinylpyrrolidone molecular weights and concentrations

Preparation and Characterization of PES/SPSF Blend Ultrafiltration Membrane

Effects of Compatibility Difference in the Mixed Solvent System on the Performance of Ppes Hollow Fiber Uf Membrane

Effect of Formamide on Structure and Performance of PES, PPESK Ultrafiltration Membrane

Preparation and Characterization of Novel Polyether Sulphone Ultrafiltration Membranes