Abstract:Polyethersulfone (PES) hollow fiber ultrafiltration (UF) membranes were fabricated using methanol, ethanol, n-propanol as well as water as additives and N-methyl-2-pyrrolidone (NMP) as a solvent. Asymmetric hollow fiber UF membranes were spun by wet and dry/wet phase inversion method from 18wt.% solids of PES/non-solvent/NMP solutions. The non-solvents were methanol, ethanol, n-propanol and water while the external coagulant was water. Effects of non-solvent and ethanol concentrations in the dope solution and air-gap distance on morphology and separation performance of PES hollow fiber UF membranes were investigated. UF membranes were characterized in terms of their solubility parameter difference, pore size and pore density measurements, scanning electron microscope (SEM) while UF experiments were conducted using polyethylene glycol (PEG 10,000 MW) and two kinds of proteins, lysozyme (14,400 MW) and chicken egg albumin (CEA 45,000 MW) as a solute. It was found that the PES UF membrane morphology changed slowly from long and wide finger-like structure through a thin finger-like structure to the sponge-like structure with some voids as ethanol concentration in the dope solution increased from 0 to 25wt.% using 90:10 NMP/H2O as a bore fluid; pure water permeation fluxes (PWP) increased from 47 to 167L/(m2·h·bar) while rejections of PEG 10,000 and two protein for wet-spun PES hollow fiber membranes were increased within less than 10wt.% ethanol concentration and then decreased with an increase of ethanol concentration. Experimental results illustrated that PWP flux and solute rejection of the dry/wet-spun fibers were higher than that of the wet-spun fibers when 15wt.% ethanol and 15wt.% methanol were used as additives. PWP flux of PES hollow fibers using 25wt.% n-propanol and 7.5wt.% water (dry/wet) as additives in the dope solution were higher while their rejections were lower. In addition, the pore sizes of internal surfaces of PES hollow fiber membranes were controlled by adjusting the ethanol or methanol concentration in the dope solution. Using above method, PES hollow fiber UF membrane with high PWP could be prepared while the molecular weight cut-off of PES hollow fiber membranes is approximately 10,000.

Facile membrane preparation strategy to reinforce permeability of polyethersulfone (PES) micro-ultrafiltration membrane for drinking water treatment

Fabrication of High-Flux PTFE Hollow Fiber Membranes Through Nonionic Surfactant Infiltration Coupled with Mussel-Inspired Chemistry Coating

Preparation and Performance of Polyethersulfone Hollow-Fiber Membrane

Preparation and Characterization of Polyethersulfone Microporous Membrane Via Thermally Induced Phase Separation with Low Critical Solution Temperature System

A Facile Way to Prepare Hydrophilic Homogeneous PES Hollow Fiber Membrane Via Non-Solvent Assisted Reverse Thermally Induced Phase Separation (RTIPS) Method

Engineering High-Effective Antifouling Polyether Sulfone Membrane with P(Peg-Pdms-Kh570)@Sio2 Nanocomposite Via In-Situ Sol-Gel Process

Preparation of PDMS/PES hollow fiber composite pervaporation membrane

Polyethersulfone (PES) hollow fiber ultrafiltration membranes prepared by PES/non-solvent/NMP solution

Preparation Of Micro-Porous Polyethersulphone Hollow Fibre Membranes Using Non-Solvent Vapour-Induced Phase Separation

Hydrophilic and Anti-Fouling Polyethersulfone Ultrafiltration Membranes with Poly(2-Hydroxyethyl Methacrylate) Grafted Silica Nanoparticles As Additive

A Polyethersulfone–bisphenol Sulfuric Acid Hollow Fiber Ultrafiltration Membrane Fabricated by a Reverse Thermally Induced Phase Separation Process

Fabricating PES/SPSF membrane via reverse thermally induced phase separation (RTIPS) process to enhance permeability and hydrophilicity

Overview of Research Progress at Home on Development of Polyethersulfone(PES)Based Ultrafiltration Membrane

Development of hydrophilic PES membranes using F127 and HKUST-1 based on the RTIPS method: Mitigate the permeability-selectivity trade-off

Fabrication and performance evaluation of an innovative asymmetric polyethersulfone composite membrane for efficient methyl blue filtration

Conductive Polyethersulfone Membrane Facilely Prepared by Simultaneous Phase Inversion Method for Enhanced Anti-Fouling and Separation under Low Driven-Pressure.

Preparation and Chlorine-Tolerant Performance of Piperazine-Fluoropolyamide Contained PES Hollow Fiber Nanofiltration Membranes

Construction of PES membranes using NH2-MIL-125 and Pluronic F127 via RTIPS method toward elevated ultrafiltration, antifouling and self-cleaning performance

Improved Antifouling Properties of Poly(Ether Sulfone) Membrane by Incorporating the Amphiphilic Comb Copolymer with Mixed Poly(Ethylene Glycol) and Poly(Dimethylsiloxane) Brushes

Multifunctional porous materials with simultaneous high water flux, antifouling and antibacterial performances from ionic liquid grafted polyethersulfone

Bimetallic polyphenol networks structure modified polyethersulfone membrane with hydrophilic and anti-fouling properties based on reverse thermally induced phase separation method