Abstract:The upper and lower parts of the figure show the phase diagrams, molecular migration process, membrane formation driving force, and the final membrane structures involved in the RTIPS and NIPS methods, respectively. When the solidification bath temperature is greater than the cloud point temperature and exceeds the critical concentration, the undesirable interaction between PSE and DEG dominates the casting solution system, which leads to the enrichment of DEG to complete the phase separation, and the driving force for membrane formation is the temperature difference, which ultimately results in the formation of a homogeneous sponge pore structure; when the solidification bath temperature is lower than the cloud point temperature, the mixed solvents are exchanged with water, and the driving force for membrane formation is the osmotic pressure, which ultimately results in the formation of a finger‐like structure. Contaminated water sources from various industries pose severe environmental challenges due to their complex compositions, high toxicity, and fluctuating qualities. This study introduces a groundbreaking strategy for fabricating advanced polysulfate (PSE) ultrafiltration membranes using a novel reverse thermally induced phase separation (RTIPS) process. By manipulating the cloud point through the DMAc/DEG solvent/nonsolvent system, our work innovatively controls membrane microstructure, overcoming limitations of conventional nonsolvent‐induced phase separation (NIPS). Our findings reveal that RTIPS, when employed above the cloud point, yields PSE membranes with a unique bicontinuous sponge‐like structure, significantly improving upon conventional NIPS products. Specifically, the optimized RTIPS membranes exhibit enhanced pure water flux (916.23 vs. 336.23 LMH), larger pore sizes (0.083 vs. 0.054 μm), increased tensile strength (1.32 vs. 0.84 MPa), and improved fouling resistance (FRR 65.5% vs. 55.2%). This research pioneers a facile yet potent method for tailoring membrane properties, achieving a balance between permeability, mechanical stability, and filtration efficacy. The demonstrated success of RTIPS in enhancing PSE membrane performance not only contributes to the development of high‐performance water treatment technologies but also charts a new course in membrane science, offering a promising avenue for sustainable wastewater management solutions.

Fabricating PES/SPSF membrane via reverse thermally induced phase separation (RTIPS) process to enhance permeability and hydrophilicity

Fabrication of Hydrophilic and Sponge-Like PVDF/brush-like Copolymer Blend Membranes Using Triethylphosphate As Solvent

Fabrication of High-Flux PTFE Hollow Fiber Membranes Through Nonionic Surfactant Infiltration Coupled with Mussel-Inspired Chemistry Coating

Preparation of High Density Polyethylene/polyethylene- Block -Poly(ethylene Glycol) Copolymer Blend Porous Membranes Via Thermally Induced Phase Separation Process and Their Properties

Exploring of novel reverse thermally induced phase separation process based on preparation and characterization of polysulfate ultrafiltration membranes with bicontinuous structure

Facile membrane preparation strategy to reinforce permeability of polyethersulfone (PES) micro-ultrafiltration membrane for drinking water treatment

Development of hydrophilic PES membranes using F127 and HKUST-1 based on the RTIPS method: Mitigate the permeability-selectivity trade-off

Bimetallic polyphenol networks structure modified polyethersulfone membrane with hydrophilic and anti-fouling properties based on reverse thermally induced phase separation method

Superhydrophilic polyethersulfone (PES) membranes with high scale inhibition properties obtained through bionic mineralization and RTIPS

Preparation and Performance of Polyethersulfone Hollow-Fiber Membrane

Tailoring PES membrane morphology and properties via selected preparation parameters

Construction of PES membranes using NH2-MIL-125 and Pluronic F127 via RTIPS method toward elevated ultrafiltration, antifouling and self-cleaning performance

Polysulfone Membranes Via Thermally Induced Phase Separation

Fabrication of PVDF ultrafiltration membrane using modified thermally induced phase separation: The role of amphiphilic and hydrophilic non-solvents

A study on fabrication of PVDF-HFP/PTFE blend membranes with controllable and bicontinuous structure for highly effective water-in-oil emulsion separation

Leaf-like ZIF-L as self-sacrificed template via acid induced removal for stronger negatively charged PES membranes based on RTIPS method

Constructing Microstructures of Chlorinated Polyvinyl Chloride Microporous Membranes by Non-solvent Induced Phase Separation for High Permeate Flux and Rejection Performance

Plasma etching assisted fabrication of PDA/PEI modified PVDF membranes for oil/water emulsion separation

A Facile Method to Control Pore Structure of PVDF/SiO2 Composite Membranes for Efficient Oil/Water Purification

Electrothermal composite membranes of PVDF-g-IL embedded in steel mesh: Fabrication via VIPS and separation of water-in-perfluoropolyether emulsion with high-viscosity

Fabrication of polysulfone membrane with sponge-like structure by using different non-woven fabrics