Abstract:Optimized shape anisotropy of the Fe-Co rich ferromagnetic (α 1 ) phase and the effective separation of the α 1 and α 2 phases with maximum magnetization difference—where α 2 represents a paramagnetic magnetic phase—are the key parameters for maximizing the magnetic properties of Alnico magnets. In this manuscript, efforts have been undertaken to optimize the shape anisotropy of the α 1 phase and increase the difference in magnetization and separation between α 1 and α 2 phases by fine tuning Al and Ni contents, directional solidification and magnetic field annealing methods. At first, Alnico magnets were fabricated by adjusting the content of α 2 phase followed by homogenization, magnetic field annealing at high temperature, and low-temperature tempering. Intrinsic coercivity ( H cj ) of ⁓146.0 kA/m, remanence ( B r ) of ⁓0.90 T and maximum energy density ( (BH) max ) of 46.02 kJ/m 3 are achieved in the magnet with 8.2 wt% Al and 12.8 wt% Ni treated in field of 1.5 T for 10 minutes. At the second stage, the magnet with optimal magnetic properties is directionally solidified to develop columnar grains, and then the α 1 phase is grown in the direction of the columnar grains by magnetic field annealing to enhance the (BH) max to 79.8 kJ/m 3 . The axial ratio of the α 1 phase increased significantly with the increase of the grain size, particularly in the directionally solidified magnets. The Curie temperature of the α 1 phase is noted near 1150 K, while the Curie temperature of the α 2 phase is below 400 K. The magnets demonstrated excellent temperature stability, with magnetic properties decreasing by only 10–12 % at 800 K. These results may pave the way for further development of Alnico magnets specifically for high temperature applications.

Multistep severe plastic deformation to achieve non-rare earth bulk magnets with high α-MnBi phase content

Multistep severe plastic deformation to achieve non-rare earth bulk magnets with high α-MnBi phase content

Novel Exchange-Coupled SmFe3/α-Fe Nanocomposite Magnets Fabricated by Magnetic Annealing

Synthesis of hard magnetic α-MnBi phase by high pressure torsion and field assisted annealing

Construction of High-Performance Multi-Main-phase Nd–Dy–Fe–B Sintered Magnets with Strengthened Chemical Heterogeneity

Manufacturing of Textured Bulk Fe-SmCo$_{5}$ Magnets by Severe Plastic Deformation

A Reliable Route for Relieving the Constraints of Multi-Main-phase Nd–La–Ce–Fe–B Sintered Magnets at High La–Ce Substitution: (pr, Nd)H Grain Boundary Diffusion

Defect manipulation for the coercivity enhancement of Nd-Fe-B permanent magnets

Bulk Α-Fe/nd2fe14b Nanocomposite Magnets Produced by Severe Plastic Deformation Combined with Thermal Annealing

Engineering microstructure to improve coercivity of bulk MnBi magnet

Anisotropic bulk rare-earth-free Mn-Al-(C) magnets prepared under high-stress and large-strain conditions

Influence of Severe Plastic Deformation on the Magnetic Properties of Sm‐Co Permanent Magnets

Synthesizing the Hard Magnetic Low-Temperature Phase of MnBi Alloy: Challenges and Prospects

Additive manufacturing of Ni-Mn-Sn shape memory Heusler alloy -- Microstructure and magnetic properties from powder to printed parts

Magnetic-field-induced transformation and strain in polycrystalline FeMnGa ferromagnetic shape memory alloys with high cold-workability

Tuneable Magneto-Resistance by Severe Plastic Deformation

Roadmap towards optimal magnetic properties in L1 0 -MnAl permanent magnets

Strong texture in nanograin bulk Nd-Fe-B magnets via slow plastic deformation at low temperatures

Grain boundary restructuring of multi-main-phase Nd-Ce-Fe-B sintered magnets with Nd hydrides

Chemical synthesis and coercivity enhancement of Nd2Fe14B nanostructures mediated by non-magnetic layer

Refining Alnico 8 magnets with composition optimization of matrix phase, directional solidification and magnetic field annealing