Abstract:Co-free and Ni-rich LiNi 0.95 Mn 0.05 O 2 (NM95) cathodes are expected to be widely employed in power batteries due to their high charge storage capacity and cost-effectiveness. However, the loss of Co and increase in Ni contents result in highly active surfaces and unstable structures, compromising rate capability and cyclic stability. Herein, polyaniline-polyethylene glycol (PANI-PEG) coating layer, with excellent electronic and Li-ion conductivity, is introduced on NM95 surface to enhance charge transfer properties and cyclic stability. Several material and electrochemical characterization techniques, such as XRD, SEM, EDS, TEM, XPS, 4-point probe, CV and EIS, are utilized to unveil the positive influence of PANI-PEG on electrochemical performance. The results reveal that PANI-PEG layer can promote electron and Li + conduction of NM95 due to the excellent electronic and Li + conductivities. Besides, PANI-PEG acts as protective layer to hinder the corrosion of electrolyte and suppress side reactions. It is revealed that NM95 cathode coated with PANI-PEG with a mass ratio of 4/6, exhibits excellent initial capacity, as high as 219.4 and 163.1 mAh/g at 1 C and 5 C, respectively, and maintains capacity retention of 94.7% (1 C, 100th cycle) and 79.0% (5 C, 200th) under cut-off voltage of 4.3 V ( vs . Li/Li + ). Moreover, NM95 exhibits capacity retention of 70.7% after 100 charge/discharge cycles at 1 C within voltage range of 2.7 to 4.5 V ( vs . Li/Li + ). These results indicate that coating electronic/Li + conductor is effective strategy to enhance rate performance and cyclic stability of Co-free and Ni-rich cathodes.

Constructing fast-ion-diffusion cathode-electrolyte-interphase to improve LiNi0.8Co0.1Mn0.1O2 cathode cyclic stability with composite polymer conductors

Electrochemical performance and thermal stability analysis of LiNixCoyMnzO2 cathode based on a composite safety electrolyte

Superior Stability Secured by a Four-Phase Cathode Electrolyte Interface on a Ni-Rich Cathode for Lithium Ion Batteries

Improved Cyclic Stability of LiNi0.8Mn0.1Co0.1O2 Cathode Enabled by a Novel CEI Forming Additive

Conductive Polymers Encapsulation to Enhance Electrochemical Performance of Ni-Rich Cathode Materials for Li-Ion Batteries.

Stabilizing Ni-Rich LiNi0.83Co0.12Mn0.05O2 with Cyclopentyl Isocyanate As a Novel Electrolyte Additive

Interphase Engineering for Stabilizing Ni-Rich Cathode in Lithium-Ion Batteries by a Nucleophilic Reaction-Based Additive.

Tailoring electrolyte to enable high-rate and super-stable Ni-rich NCM cathode materials for Li-ion batteries

Enhanced high-rate and cyclic performance of Co-free and Ni-rich LiNi0.95Mn0.05O2 cathodes by coating electronic/Li+ conductive PANI-PEG layer

Stabilizing Ni-rich LiNi0.8Co0.1Mn0.1O2 cathode by generating ion-conductive polymer coating layer with 1, 3-dioxolane introducing electrolyte for lithium-ion batteries

Enabling stable and high-rate cycling of a Ni-rich layered oxide cathode for lithium-ion batteries by modification with an artificial Li<SUP>+</SUP>-conducting cathode-electrolyte interphase

Conductive Cyclized Polyacrylonitrile Coated LiNi0.6Co0.2Mn0.2O2 Cathode with the Enhanced Electrochemical Performance for Li-Ion Batteries

An Interphase Engineering Method of Stabilizing Ni‐rich Cathode in Lithium‐ion Batteries by A Nucleophilic‐based Additive

Polyvinylpyrrolidone-Induced Uniform Surface-Conductive Polymer Coating Endows Ni-Rich LiNi0.8Co0.1Mn0.1O2 with Enhanced Cyclability for Lithium-Ion Batteries.

Carbonized Polymer Dots Enhancing Interface Stability of LiNi0.8Co0.1Mn0.1O2 Cathodes

Chemo-mechanical stable cathode interphase via interface in-situ catalytic-conversion integrated design for all solid-state batteries

Double Conductor Coating to Improve the Structural Stability and Electrochemical Performance of LiNi0.8Co0.1Mn0.1O2 Cathode Material

Surface Coating of NCM523 Cathode Electrodes by the Difunctional Block Copolymer/Lithium Salt Composites

Electrolytes Polymerization‐Induced Cathode‐Electrolyte‐Interphase for High Voltage Lithium‐Ion Batteries

Elevating Cycle Stability and Reaction Kinetics in Ni‐Rich Cathodes Through Tailored Bulk and Interface Chemistry for Sulfide‐Based All‐Solid‐State Lithium Batteries

Enhancing Interfacial Kinetics and Stability of LiMn2O4 Cathode by Fabricating an Artificial Cathode Electrolyte Interphase of LiNbO3