Abstract:The effects of electro-pulse on microstructure and mechanical properties of Al-Cu-Mn-Zr-V alloy were investigated, and the ageing mechanism was analyzed. As the current density increases, the size and quantity of precipitates gradually transit from continuous aggregation to dispersion at grain boundaries, and the mechanical properties are improved. When the current density is 15 A·mm−2, the precipitates are smallest and the mechanical properties are best. The tensile strength is 443.5 MPa and the elongation is 8.1%, which are 51.7% and 42.1% higher than those of conventional ageing treatment, respectively. Once the current density exceeds 15 A·mm−2, the precipitates will increase again and gather at grain boundaries, and the mechanical properties also decrease. An additional electrical free energy arising from an electro-pulse provides thermodynamic and kinetic conditions for the ageing precipitation of second phases. The electro-pulse can enhance the ageing diffusion coefficient, being improved by 34 times for 15 A·mm−2. The electro-pulse improves the nucleation rate and decreases the critical nucleation radii of second phases. However, it also accelerates the grain growth, making the second phases become coarse. An electro-pulse with a current density of 15 A·mm−2 can rapidly nucleate the second phase at 463 K while the precipitates are relatively small after growth.

Accelerated solid solution and aging induced by electropulsing in Mg-Al-Ca-Mn alloy

Effect of Electropulsing Treatment on Solid Solution Behavior of an Aged Mg Alloy AZ61 Strip

Improved Ductility of Aged Mg-9Al-1Zn Alloy Strip by Electropulsing Treatment

Effect of Electropulsing Treatment on Microstructure and Tensile Fracture Behavior of Aged Mg–9Al–1Zn Alloy Strip

On the Thermodynamics and Kinetics of Electropulsing Induced Dissolution of Β-Mg17al12 Phase in an Aged Mg–9Al–1Zn Alloy

Effects of induced electro-pulsing and aging process on properties and microstructure of 7075 aluminum alloy

Study on the Microstructure Evolution and Mechanical Properties of an Al-Mg-Li Alloy Aged by Electropulsing Assisted Ageing Processing

Influence of Electropulsing Treatment Combined with Pre-Deformation on Ageing Behavior and Mechanical Properties of 5A90 Al-Li Alloy

Mechanism of Electropulsing Induced Recrystallization in a Cold-Rolled Mg–9Al–1Zn Alloy

Microstructure and Mechanical Properties of Cold-Rolled Mg-6Al-1Zn Alloy Strip Treated by Electropulsing Treatment

The Effect of Multiple Pulse Treatment on the Recrystallization Behavior of Mg-3al-1zn Alloy Strip

Influence of Electropulsing Treatment on Microstructure and Mechanical Properties of Cold-Rolled Mg–9Al–1Zn Alloy Strip

Microstructure and texture evolution of the cold-rolled AZ91 magnesium alloy strip under electropulsing treatment

Improved Plasticity of Mg–Al–Zn Alloy by Electropulsing Tension

Improved Mechanical Properties of Mg–9Al–1Zn Alloy by the Combination of Aging, Cold-Rolling and Electropulsing Treatment

Optimizing strength and ductility in 7150 Al alloys via rapid electropulsing cyclic heat treatment

Effect of Pulsed Magnetic Field on Microstructure and Mechanical Properties of 7050 Al Alloy After Two-Stage Aging

Mechanism of an acceleration in T1 precipitation kinetics in an Al-Cu-Li alloy by electropulsing

Effect of Electro-Pulse on Microstructure of Al-Cu-Mn-Zr-V Alloy during Aging Treatment and Mechanism Analysis

Enhancement of Ductility in Mg-3Al-1Zn Alloy with Tilted Basal Texture by Electropulsing

Thermal and Electromigration Effects of Electropulsing on Dynamic Recrystallization in Mg–3Al–1Zn Alloy