Abstract:The Laser Powder Bed Fusion (LPBF) process offers the capacity to produce parts with complicated geometries that cannot be manufactured using traditional manufacturing processes. The aerospace industry is particularly interested in this capability because it may enable the creation of high-temperature structural parts with sophisticated cooling channel layouts. This would allow future gas turbines to operate at higher temperatures, resulting in higher efficiency. However, if they are to realize this promise, they must first enhance their knowledge of the influence of the LPBF process on alloy microstructures and its subsequent effect on mechanical properties. Furthermore, this study offers information on how to comprehend microstructural development and the impact it has on the mechanical characteristics of the CM247LC alloy processed by LPBF. Using the Direct Metal Laser Sintering technique based on Laser Power Bed Fusion, the CM247LC nickel-based superalloy was manufactured. When the CM247LC alloy was examined microscopically, carbides and cracks (both straight and serrated) were found. Electron Backscatter Diffraction studies revealed elongated grains in the longitudinal section and equiaxed clusters in the transverse section. Longitudinal sections have been determined to be predominantly composed of columnar grains with cells that have an average size of 0.7 μm. The γ/γ′ eutectic, as well as highly concentrated precipitates and highly concentrated dislocations, separate these cells from neighboring cells and grains. Up to 10 nm of the γ′ can be found inside the cells, despite having a diameter of up to 40 nm at the cell walls. The calculated rate of cooling during solidification is around 10 6 K/s based on the observed cell diameters. Tensile tests on samples that had just been manufactured reveal that yield strength is comparable to previous studies. High precipitate concentrations, dislocations density, fine cell structure, and γ' inside cells are interpreted as the sources of high strength in as-fabricated conditions.

Wear properties of Fe-16Mn-10Al-5Ni-0.86C lightweight steel manufactured by laser powder bed fusion

Effect of Surface Modification on the High Temperature Low Cycle Fatigue Performance of LPBF 316L Austenitic Steel

Wear Behavior of AlSi10Mg Alloy Produced by Laser‐Based Powder Bed Fusion and Gravity Casting

Unconventional wear characteristics due to perfect plasticity in laser powder bed fusion processed 316 L stainless steel

Metallurgical reactions and tribological properties of self-lubricating Al-WS2 composites: Laser powder bed fusion Vs. spark plasma sintering

Microstructure effect on sliding wear of 316L stainless steel selectively laser melted

Developing a novel lightweight Al–Mg–Li alloy for laser powder bed fusion additive manufacturing: Parameter optimization, microstructure evolution, and mechanical performance

Structural Characterization and Strength Assessment of Laser Powder Bed Fusion Manufactured CM247LC Nickel Based Super Alloy

Laser powder bed fusion of a tungsten-nickel-ferrum alloy via in-situ alloying: Densification, microstructure, and mechanical properties

Laser powder bed fusion of a novel nano-modified tungsten alloy with refined microstructure and enhanced strength

Tribological performance of a novel 7068-aluminium/lightweight-high-entropy-alloy fabricated via powder metallurgy

Microstructure, Tensile, and Fatigue Properties of Large-Scale Austenitic Lightweight Steel

A high Fe-containing AlSi12 alloy fabricated by laser powder bed fusion

A data-driven framework to improve the wear resistance of a low-alloy steel fabricated by laser powder bed fusion

Effect of loading on microstructure and friction and wear behavior of an austenite lightweight steel

Deformation-Induced Strengthening Mechanism in a Newly Designed L-40 Tool Steel Manufactured by Laser Powder Bed Fusion

Effect of Post-Manufacturing Heat Treatment on Wear Performance of Laser Powder Bed Fusion 316L Stainless Steel Under Various Normal Loads

Effects of the microstructure and texture characteristics on mechanical properties of the Al–Ni–Cu–Fe alloy manufactured by laser powder bed fusion

Laser Powder Bed Fusion of a Non-Equiatomic FeNiCoAl-based High-Entropy Alloy: Printability, Microstructure, and Mechanical Properties

Comparison of Performance of Laser Powder Bed Fusion Thin-Walled TC11 Alloy Samples Welded Via Laser Welding and Electron Beam Welding

Fretting wear behavior on LPBF processed AlSi10Mg alloy for different heat treatment conditions