Abstract:Laser-based powder bed fusion (LPBF) is a widely utilized technique for additive manufacturing (AM) of metal components. The size of LPBF-produced parts is restricted by machine dimensions. Welding emerges as a feasible solution for connecting smaller parts generated via PBF. Nevertheless, the weldability of PBF parts differs from conventional ones due to the unique thermal history of PBF components. This paper investigated the weldability of stainless steel 316L and tensile behavior of welded samples, comparing samples produced through LPBF and the conventional wrought method. Tensile testing, grain size analysis, microhardness test, and assessment of secondary dendrite arm spacing were conducted on every welded combination of materials (AM-AM, wrought-wrought, and AM-wrought) using gas tungsten arc welding (GTAW). The findings indicate that the wrought material demonstrates a higher maximum strength (577.5 MPa) and a lower yield strength (231.7 MPa) compared to the AM material (with a maximum strength of 548.2 MPa and a yield strength of 399.9 MPa). This difference may be attributed to the annealing process applied to the wrought material, which has not been applied on the AM material. Additionally, welded wrought samples have a significantly lower tensile strength compared to non-welded samples. The wrought samples exhibit a larger average grain size (11.14 to 31.12 ) in the heat affected zone (HAZ) compared to non-heat affected regions (8.13 ). In contrast, it is found that grain coarsening does not occur in PBF samples, which exhibit a similar grain size in the HAZ (15.04 ) vs 13.97 outside of the HAZ. Larger grain sizes within the HAZ correspond to a larger reduction in tensile strength for the wrought samples, compared to PBF samples. Similar secondary dendrite arm spacing has been observed in the weld regions of both PBF and wrought materials. Microhardness test results indicated that the AM base material has the highest microhardness and gradually decreases as transitioning to the HAZ and weld region. In summary, the PBF samples exhibit less reduction of strength and ductility after welding than wrought samples. Therefore, it is determined that additively manufactured 316L stainless steel has a higher weldability than traditionally manufactured wrought 316 stainless steel.

Unconventional wear characteristics due to perfect plasticity in laser powder bed fusion processed 316 L stainless steel

Microstructure effect on sliding wear of 316L stainless steel selectively laser melted

Strengthening Mechanisms and Strain Hardening Behavior of 316L Stainless Steel Manufactured by Laser‐Based Powder Bed Fusion

Effect of Surface Modification on the High Temperature Low Cycle Fatigue Performance of LPBF 316L Austenitic Steel

A comprehensive study of LPBF parameter influence in 316L stainless steel mechanical properties, macrostructure, and printability

Effect of Post-Manufacturing Heat Treatment on Wear Performance of Laser Powder Bed Fusion 316L Stainless Steel Under Various Normal Loads

Fatigue and tensile deformation behaviors of laser powder bed fused 304L austenitic stainless steel

Fatigue Response of Additive-Manufactured 316L Stainless Steel

Effects of gas tungsten arc welding on the mechanical properties and microstructure of 316L stainless steel by powder bed fusion

Creep-fatigue Properties and Deformation Mechanism of 316L Steel Fabricated by Laser Powder Bed Fusion (PBF-LB/M)

Effect of heat treatment and electroless Ni-P coating on mechanical property and corrosion behaviour of 316L stainless steel fabricated by laser powder bed fusion

Comparison of the microstructure, mechanical properties and distortion of stainless steel 316 L fabricated by micro and conventional laser powder bed fusion

Exploring structural origins responsible for the exceptional mechanical property of additively manufactured 316L stainless steel via in-situ and comparative investigations

Deformation Mechanisms of Selective Laser Melted 316l Austenitic Stainless Steel in High Temperature Low Cycle Fatigue

High-power laser powder bed fusion of 316L stainless steel: Defects, microstructure, and mechanical properties

Tailoring the Microstructural and Mechanical Properties of 316L Stainless Steel Manufactured by Laser Powder Bed Fusion

Mechanical properties and microstructural characteristics of 316L stainless steel fabricated by laser powder bed fusion and binder jetting

Laser Powder Bed Fusion of 316L Stainless Steel: Effect of Laser Polishing on the Surface Morphology and Corrosion Behavior

Micro-Scale Deformation Aspects of Additively Fabricated Stainless Steel 316L under Compression

Pitting Corrosion in 316L Stainless Steel Fabricated by Laser Powder Bed Fusion Additive Manufacturing: A Review and Perspective

Microstructure and Fatigue Behavior of Laser-Powder Bed Fusion Austenitic Stainless Steel