Abstract:Good gas permeability is an essential factor for the smooth operation and high performance in the lower part of the blast furnace. Under the present low carbon blast furnace smelting conditions, the coke layer is thinner, and the proportion of the molten metal in the coke layer is significantly higher, resulting in a major reduction in gas permeability, which seriously affects blast furnace operations. Also, the lower thickness of the coke layer weakens the process of solid-liquid carbon dissolution when the molten iron passes through the coke layer, which reduces the carbon content of the molten iron and further deepens the erosion of the refractory by the unsaturated molten iron. The carbon dissolution in the molten iron in a blast furnace core was measured by a high-temperature vacuum wettability test tool that analyzed the interface wetting activity between Fe−C melts with specific carbon mass fraction (3.8%, 4.3%, 4.8%) and 99.9% of high temperatures graphite plates. Besides, the scanning electron microscope (SEM) and energy dispersive spectroscopy (EDS) were used to analyze the graphite substrate’s carburizing morphology and carburizing distances. The results show that, with the increase of carbon content, the interface contact angle becomes bigger. The contact angle decreases with time, and eventually reaches a steady-state during the melting process, and the Fe−C melt with saturated carbon cannot be wet. The scanning electron microscopy analysis shows that a spherical cap-like depression is created by a cross-section of the Fe−C melt and the graphite substrate, and the radius and volume of the depression decrease with increasing carbon content. The study of the EDS scanning analysis shows that the amount of dissolved carbon atoms in the graphite substrate penetrates the Fe−C melt and decreases with increasing initial carbon concentration. The smaller the carburizing effect, the better the wetting is conducive to carbon mass transfer. It is found that by measuring carburizing of the carbon atoms in the graphite substrate into the Fe−C melt by calculating the surface energy reduces the surface energy between the two. Thus, the surface tension decreases and the melt spreads slowly with contact angle gradually decreasing during melting.

Enhanced reduction of multiple layers carbon containing pellets in rotary hearth furnace

Numerical Analysis of Radiative Heat Transfer and Direct Reduction of Three-Dimensional Multilayer Ellipsoidal Carbon-Containing Pellet Unit in the Rotary Hearth Furnace

Effect of different forms of carbon on the reduction behaviour of iron ore-carbonaceous material composite pellets in multi-layer bed rotary hearth furnace (RHF)

A Computational Study on the Reduction Behavior of Iron Ore/Carbon Composite Pellets in Both Single and Multi-layer Bed Rotary Hearth Furnace

Reduction and Melting Behavior of Pre-reduction Metallized Carbon-Bearing Pellets in Iron Bath Smelting Reduction Furnace

Modeling of Thermochemical Behavior in an Industrial-Scale Rotary Hearth Furnace for Metallurgical Dust Recycling

Fundamental Study on Utilization of Titanium Resources by RHF Process

Experimental Study on Impact of Iron Coke Hot Briquette As an Alternative Fuel on Isothermal Reduction of Pellets under Simulated Blast Furnace Conditions

Direct Reduction of Iron Ore Pellets by Using CO/CO2 and CO Gases

EXPERIMENTAL STUDY ON THE REDUCTION OF IRON ORE AND COAL MIXED PELLETS OF HIGH PHOSPHORUS HEMATITE PRE-TREATED BY MICROWAVE IRRADIATION

Numerical Investigation of the Limit of Coke Rate Reduction in an Ironmaking Blast Furnace (BF)

Effects of direct reduction process on the microstructure and reduction characteristics of carbon-bearing nickel laterite ore pellets

Study on the reduction of Fe2O3 pellets by CO-CO2 and H2-H2O: Reaction kinetics and pore network model

Analysis of the melting process of carbon-bearing pellets in iron bath, slag bath and graphite crucible

An efficient and clean utilization technique for red mud based on fluidized bed carbon monoxide reduction

Experimental and Numerical Simulation Study on Reduction of Pellets Based on X-ray Micro-computed Tomography

Study on gas-based reduction mechanism of ultra-high-grade pellets with high basicity by experiment tests and first-principles calculation

Interface Wetting Behavior Between Iron and Coke During the Carbon Dissolution Process in a Blast Furnace

Process and mechanism of preparing metallized blast furnace burden from metallurgical dust and sludge

Phase Evolution Behavior during the Reduction Process of Medium‐Silica Fluxed Pellets

Reduction of Iron‐Ore Pellets Using Different Gas Mixtures and Temperatures