Abstract:The Centrifugal compressor is a piece of key equipment for petrochemical factories. As the core component of a compressor, the blades suffer periodic vibration and flow induced excitation mechanism, which will lead to the occurrence of crack defect. Moreover, the induced blade defect usually has a serious impact on the normal operation of compressors and the safety of operators. Therefore, an effective blade crack identification method is particularly important for the reliable operation of compressors. Conventional non-destructive testing and evaluation (NDT&E) methods can detect the blade defect effectively, however, the compressors should shut down during the testing process which is time-consuming and costly. In addition, it can be known these methods are not suitable for the long-term on-line condition monitoring and cannot identify the blade defect in time. Therefore, the effective on-line condition monitoring and weak defect identification method should be further studied and proposed. Considering the blade vibration information is difficult to measure directly, pressure sensors mounted on the casing are used to sample airflow pressure pulsation signal on-line near the rotating impeller for the purpose of monitoring the blade condition indirectly in this paper. A big problem is that the blade abnormal vibration amplitude induced by the crack is always small and this feature information will be much weaker in the pressure signal. Therefore, it is usually difficult to identify blade defect characteristic frequency embedded in pressure pulsation signal by general signal processing methods due to the weakness of the feature information and the interference of strong noise. In this paper, continuous wavelet transform (CWT) is used to pre-process the sampled signal first. Then, the method of bistable stochastic resonance (SR) based on Woods-Saxon and Gaussian (WSG) potential is applied to enhance the weak characteristic frequency contained in the pressure pulsation signal. Genetic algorithm (GA) is used to obtain optimal parameters for this SR system to improve its feature enhancement performance. The analysis result of experimental signal shows the validity of the proposed method for the enhancement and identification of weak defect characteristic. In the end, strain test is carried out to further verify the accuracy and reliability of the analysis result obtained by pressure pulsation signal.

Classification of internal defects of gas turbine blades based on the discrimination of linear attenuation coefficients

Defect Detection on a Wind Turbine Blade Based on Digital Image Processing

Development of Digital-Image-Correlation Technique for Detecting Internal Defects in Simulated Specimens of Wind Turbine Blades

A Hybrid Modeling Method of Fatigue Crack Growth for Gas Turbine Blades under Combined High and Low Cycle Fatigue Loadings

Degradation Behavior of Microstructures and Mechanical Properties of GTD111 Turbine Blade After Long-Term Service

Study on Discrete Modeling Method of Modal Testing for Turbine Blade

Damage Mode Identification of Composite Wind Turbine Blade under Accelerated Fatigue Loads Using Acoustic Emission and Machine Learning

Fatigue Damage Evaluation of Compressor Blade Based on Nonlinear Ultrasonic Nondestructive Testing

Exact Localization of Debonding Defects in Thermal Barrier Coatings

Weak Defect Identification for Centrifugal Compressor Blade Crack Based on Pressure Sensors and Genetic Algorithm

Defect detection and classification of offshore wind turbine rotor blades

Classification of Demagnetization Faults based on Performance Evaluation of Machine Learning Algorithms via Flux and Vibration Signals in Permanent Magnet Wind Turbine Generator

Worn area modeling for automating the repair of turbine blades

Gapped Smoothing Algorithm Applied to Defect Identification Using Pulsed Thermography

Static Strength Tests and Effects of Defects on Dovetail Elements of Ceramic Matrix Composites Turbine Rotor Blades

Gas turbine blade fracturing fault diagnosis based on broadband casing vibration

Performance Evaluation of Damaged Blades Using Numerical Simulation and Machine Learning

Damage detection and full surface characterization of a wind turbine blade using three-dimensional digital image correlation

Study on Air Bubble Defect Evolution in Wind Turbine Blade by Infrared Imaging with Rheological Theory

Machine Learning Based Classification Model for Predicting Cyclic Failure in Radially Cooled Gas Turbine Blades

Automated Crack Detection With Image Analysis for the Blades of Steam Turbine