Abstract:To get the actual service temperature distribution of turbine blades in aeroengines is very important for the design and maintenance. However, the acquisition of service temperature distribution has always been a challenge due to the complex and severe working condition of turbine blades. In this work, one turbine blade made of directionally solidified DZ125 superalloy was investigated after the service in air for 900 h. The microstructural evolution of DZ125 superalloy after thermal exposure at 9004100 t without the stress in different time period was also investigated, for comparison. According to microstructural degradation behaviors in the dendritic region, interdendritic region, carbides and grain boundary of DZ125 superalloy before and after service, the volume fraction of gamma' precipitates in the dendritic region was determined as the quantitative characterization parameter. A method to evaluate the service temperature of turbine blades was developed, based on the quantitative characterization of microstructural evolution, such as the relationship between the thermally exposured temperature and volume fraction of gamma' precipitates. The equivalent average service temperature (T-ave) and the equivalent maximum service temperature (T-max) were proposed based on the assumption of the constant temperature during service and the nearly service condition with variable temperature of blades, respectively. The results indicate that the service temperature was higher in the middle of the blade, and became lower at the locations closer to the tip or the root. For each cross-section, the service temperatures of the serviced blade in the descending order were leading edge, pressure side, trailing edge and suction side. The highest service temperature of 1050 similar to 1100 degrees C appeared at the leading edge in the middle of the blade. The distribution trend of T-ave agreed well with that of T-max but T-max. was higher than T-ave in some locations of the blade. This work suggests that the evaluation results of T-max were more reasonable than those of T-ave. This method would be helpful to establish the assessment method of the service-induced microstructural damage in turbine blades made of directionally solidified superalloys.

Degradation Behavior of Microstructures and Mechanical Properties of GTD111 Turbine Blade After Long-Term Service

Microstructure Degradation of Service-Exposed Turbine Blades Made of Directionally Solidified DZ125 Superalloy

Dependence of Microstructural Evolution on the Geometric Structure for Serviced DZ125 Turbine Blades

Degradation of Microstructural and Mechanical Properties with Serviced Turbine Blades

Structural Degradation and Elemental Variations in an Ex-Service First-Stage Gas Turbine Blade

Microstructural Evolution and Deformation Features in Gas Turbine Blades Operated In-Service

Assessment of service induced degradation of microstructure and properties in turbine blades made of GH4037 alloy

Microstructural Deterioration Mechanism of Directionally Solidified Ni-Based Superalloy Used in First-Stage Industrial Gas Turbine Blades after Ultra Long-Term Service

Service Induced Degradation and Rejuvenation of Gas Turbine Blades

Evaluation of Service-Induced Microstructural Damage for Directionally Solidified Turbine Blade of Aircraft Engine

Mechanical Properties Deterioration and Its Relationship with Microstructural Variation Using Small Coupons Sampled from Serviced Turbine Blades

Quantitative Characterization and Assessment of Served Rene N5 Ni-based Single Crystal Industrial Gas Turbine Blade

Evaluation of Microstructural Degradation in a Failed Gas Turbine Blade Due to Overheating

Quantitative Characterization and Assessment of Served René N5 Ni-based Single Crystal Industrial Gas Turbine Blade

The investigations of rejuvenation heat treatment on the microstructure and mechanical properties of a serviced gas turbine blade

Microstructure and mechanical degradation of K403 Ni-based superalloy from ultra-long-term serviced turbine blade

Study on Mechanical Properties of DZ125 Directional Solidification Turbine Blades in Different Positions

EVALUATING SERVICE TEMPERATURE FIELD OF HIGH PRESSURE TURBINE BLADES MADE OF DIRECTIONALLY SOLIDIFIED DZ125 SUPERALLOY BASED ON MICRO-STRUCTURAL EVOLUTION

Tensile property of a modeling specimen of DD6 single crystal cooling turbine blade

Microstructural Degradation and Mechanical Properties of Gh4033 Alloy after Overheating for Short Time

Direct Investigation on High Temperature Tensile and Creep Behavior at Different Regions of Directional Solidified Cast Turbine Blades